How To Break In A Baseball Glove In The Oven

How to Break in a Baseball Mitt in the Oven

The most effective way to break in a baseball glove is to use it, yet you could find yourself with a new mitt and a game in the following few days. To break in your glove, heat from your oven, coupled with oil or foam to keep the leather supple, are all effective methods. Your mitt will be ready for your next game in no time. Wet the mitt thoroughly, including the leather ties, to ensure proper fit. Do not wet the mitt; instead, lightly damp it to ensure that it does not dry out too much in the oven.

Preheat the oven to 350 degrees Fahrenheit (180 degrees Celsius).

Using a cookie sheet, place your mitt in the preheated oven for a few minutes.

Check on your mitt every few minutes to ensure that it is being warmed uniformly throughout.

  • During the first 10 minutes of cooking, move it about as much as you can while it is still warm.
  • Put an elastic or string around a ball and tuck it into the pocket of your mitt before putting it back in the oven for the last time.
  • Continue to break in your baseball mitt by softly rubbing it with mink oil on a daily basis.
  • It is important not to apply too much oil, since this might make your glove damp and cause the leather to degrade faster than normal.


Continue to practice on your mitt by playing catch and tying a baseball in your pocket at night to keep it sharp.


This approach should not be used with baseball gloves made of plastic or vinyl. This is only applicable to leather gloves. It’s important not to tuck the ball into the pocket too firmly, as the twine or elastic may cause wrinkles in the mitt.

How do you want your new baseball glove: baked, steamed or wrapped?

Welcome to the process and ritual of breaking in a new glove that is a part of every American spring. As with anything in baseball, there are a hundred different points of view on the appropriate method to do something, each of which is fiercely defended. According to glove gurus, some more guru than others, a stiff new glove should be treated as either your closest buddy or roadkill depending on its condition. You can drown a glove, roast it, or drive it over with a car, but none of these methods are particularly effective.

  • A new catcher’s glove is apparently subjected to a wild assault by Tony Pena, the former big league backstop and current New York Yankees bench coach.
  • In effect, what Pena is doing is speeding up the regular wear and tear that a glove would experience, which is exactly what all of the sometimes-sensible, sometimes-bizarre strategies are seeking to accomplish.
  • To soften a glove, heat it in the microwave for a few seconds.
  • However, if your microwave has metal grommets — sorry, Mom — this will immediately cause it to malfunction.
  • Chefs take note: It also has the additional effect of hastening the degeneration of the glove.
  • ‘It will get too soft, and the ball will pop right out,’ says the scout.
  • The pros, on the other hand, adopt the opposite approach.
  • After that, they may grease it or spread it with shaving cream (lanolin is the secret ingredient), and then begin shagging baseballs.

“Most of the time, they’ll have two gloves: one for use in games and another for breaking in for the future.” “I’ve been doing this for more than 40 years, and I’m well acquainted with the dunking.” Paul Roberts, owner of Landry’s sports goods in Montrose, says the product “doesn’t dry out properly.” Roberts believes that dunking may be effective for professionals, who are provided with free gloves.

  1. However, for recreational league players who wish to use their gloves for several seasons, dunking damages the lacing and accelerates the degeneration of the glove.
  2. Plucking out the glove with a mallet, applying conditioning oil, heating the glove, and sealing it with Neet’s Foot or another light oil are all steps in this process.
  3. “It reduces break-in time by around 70%,” he says of the procedure.
  4. Until a generation or two ago, gloves did not have large pockets for holding things.
  5. A number of technological advancements in webbing and materials have occurred since then, including composite backs, nylon stitching, plastic and Styrofoam fills, none of which has been very advantageous to customers.
  6. The renowned Chilton, who has been referred to as “the Wolfman Jack of glove repair,” claims to have seen a decline in the quality of leather in the late 1960s, when cattlemen began to move from ranges to feedlots.
  7. As a result, “they don’t use a fraction of the leather they used to,” adds Chilton, who also advises avoiding submerging in water since it produces mildew and dry rot.
  8. Wrap the glove in the heated towel to create a steaming effect similar to that of steaming a pot of water.
  9. What Wilson advises, and which is similar to Chilton’s method, is as follows: Using the hottest tap water available, soak a towel and thoroughly wash clean the glove.

This wet-and-catch procedure should be repeated for five consecutive days. After the glove has dried entirely on the fifth day, completely oil it. [email protected]

How to Break in a Baseball Glove (The Right Way) –

Investing in a high-quality baseball glove is one of the most essential decisions a baseball or softball player can make about their game. FREE 1 Hour Coaching Clinic with MLB Hitting CoachWatch Clinic in conjunction with the MLB Hitting CoachWatch Clinic Now It may make a significant difference in your overall performance if you select the proper glove for your position and playing style. While no one glove can transform you into a great defender, selecting one that fits properly and feels comfortable may help you gain more confidence on the field and produce plays that are more clean and consistent in their execution.

Even if you choose a model that is somewhat below the “elite” level, you should expect to pay between $150 and $250 for a quality leather mitt.

One component of this is ensuring that it is properly broken in.

Unfortunately, there is a lot of disinformation out there about the appropriate and wrong procedures, and if you aren’t cautious, you might end up doing more harm than good.

How to Break in a Baseball or Softball Glove

Greetings and congratulations on your recent purchase! Premium leather gloves are pricey, but they demonstrate that you are dedicated to the game and are prepared to go to the next level. Top models such as the Wilson A-2000 and the Rawlings Heart of the Hideare expensive, but if you take good care of and preserve your new glove, it will be at your side for many seasons to come.

Why Do Baseball Gloves Need to be Broken In?

One of the characteristics that distinguish leather as a valued and flexible material is its long-term resilience. However, unused leather that has just been pulled off the production line is typically as rigid as a rock, and the leather used by baseball glove makers is no exception to this rule. Those of you who have ever attempted to catch a ball with a brand new glove are well aware of the difficulties involved. They’re nearly hard to close, and the ball bounces out as if it had been thrown against a wall of bricks.

The break-in phase might be anywhere from a few days to many weeks, depending on the type of leather used.

How to Break in a Baseball Glove – The Right Way

Nomar Garciaparra, a former Boston Red Sox shortstop, had one rule: no one else’s hand was permitted to be in his glove at any time. Nomar’s rule is a frequent one among great baseball players, and with good reason. Since leather expands and conforms to your hand and motions as you break in a glove, it becomes more comfortable and supportive. You want a glove that feels natural in your hand, as if it’s an extension of your arm that you forget is even there.why That’s the best way to break in a glove — and the one you should opt for, if at all possible — is also the most straightforward: catch baseballs with it.The best way to break in a glove is also the most straightforward: catch baseballs with it.

With time and repetitions, the glove will organically shape to your hand, providing you with a bespoke fit and a pocket that’s tailored to how you catch the ball.

It is also important to note that playing catch does not damage the leather of the glove, which is a risk associated with some of the expedited methods discussed in this article.

So throw, take ground balls, shag fly balls, and catch any ball with your hand in the glove whenever you have the opportunity. It will take some time, but it will be well worth it in the end.

How to Break in a Baseball Glove Fast

When it comes to breaking in a glove, a mix of warm water and manhandling is the most efficient method. Shigeaki Aso, a glove expert for Wilson Sporting Goods and one of the world’s foremost authorities on the subject, explains the procedure in the video below. What you’ll need is the following:

  • A pail of hot water (not boiling)
  • A pair of rubber gloves a cup of anything
  • A softer surface (such as a cushion or a rug)
  • Glove mallet/glove hammer (optional).

However, it’s important to note that, despite Aso’s well-deserved reputation, there is considerable controversy about the effectiveness of his technique in general. Aso is a highly skilled leather craftsman who creates some of the best gloves available anywhere in the world. He’s well aware of what he’s doing. Using water to soften the leather makes it simpler to work with, but if the water is not applied appropriately, it might leave the leather dry and brittle. So, if you decide to go this route, make sure to follow the directions to the letter – and keep in mind that making a mistake might result in damage to your mitt.

  1. Glove mallet from the Mizuno brand, with a rounded end.
  2. Using this method, you may loosen up the leather and make it more pliable.
  3. With the glove still slightly damp, you want to concentrate on applying as much pressure as possible to the region indicated by the yellow arrow in the illustration below.
  4. It is at this point that the glove mallet is utilized.
  5. Another fantastic approach to form the pocket from here is to place your hand in the glove and use the mallet to shape the pocket.

Glove Steaming

Steaming your glove is a simple, quick, and effective method of cleaning. The technique, on the other hand, has the potential to harm the leather’s fibers. It is for this reason that steaming will void Wilson’s one-year glove guarantee.) Using steam on your glove can soften it, but it will also decrease its durability. In addition, players frequently report that steamed leather fails to maintain its form, instead continuing to break in until it becomes almost too soft to handle. So, if you’re looking for a game-ready glove right now, this would be a good alternative.

Expect the glove to last you little longer than a season, at the very most. Allowing Dick’s to steam your glove is the quickest and most convenient option. During the steaming process, there are three processes involved:

  1. Glove conditioner will be applied by the technician, which will allow the pores on the leather to open up and soften throughout the steaming process. The technician will place the mitt in a glove steamer, which will soften the leather, allowing it to be more pliable. Taking the mitt out of the bag, the technician will begin striking it with a mallet, loosening up the crucial places. It is likely that this process will be repeated several times.

Glove Wrapping

A good supplemental approach to aid in the break-in of your glove is to wrap it around your hand. There are two schools of thought on how to wrap a gift: one believes that a ball should be placed in the pocket and the other believes that it should not. The only one of those suggestions is right; you should always wrap your glove around a ball that is in the pocket. (You may find out more about why this is the case in the section on the mattress approach, which follows.) Wrapping your glove is a simple technique that takes only a few minutes.

  1. The glove is closed (with a ball in the pocket) by bringing the pinky and thumb together. Make a secure closure for the glove by wrapping it with thread, elastic, rubber bands, or anything else that will keep it in that closed position. Allow it to rest for a couple of days before unwrapping it and repeating the procedure

Wrapping the glove stretches the leather and retains it in place for a longer amount of time, making it simpler to deal with in the future.

Glove Conditioners and Oils

Conditioning and nourishing oils for gloves can be used both during and after the break-in process. The first rule of thumb when it comes to utilizing glove conditioners and oils is to only use items that have been approved by the manufacturer. Don’t apply Vaseline, petroleum jelly, chapstick, or olive oil on your glove since they will harm and/or saturate the leather, according to the manufacturer (leaving it greasy, heavy or dried out). The following are five of the most popular conditioners on the market.

  1. Nokona Classic Leather Glove Conditioner
  2. Mizuno Strong Oil Glove Conditioner
  3. Rawlings Glovolium Glove Treatment
  4. Wilson Pro Stock Glove Conditioner
  5. Wilson Pro Stock Mink Oil Paste
  6. Wilson Pro Stock Mink

It’s important to remember that a little goes a long way with oils and conditioners. For the most part, you’ll only need to apply a thin layer of coating and gently massage it in with a clean cloth. Essentially, the purpose of these items is to keep leather in good condition while also, in certain instances, softening it. Using too much can result in saturation, which can result in the glove becoming ruined. Another thing to consider is that, in most cases, you will not be required (or even desired) to soften your glove’s webbing, which is typically thinner than the glove’s body and should break in quite rapidly on its own.

The Wrong Way to Break in a Baseball Glove

It’s important to remember that a little goes a long way when using oils and conditioners. It is usually sufficient to apply a little layer and gently massage it into the surface with a clean cloth to get the desired results. The purpose of these items is to keep the leather in good condition while also softening it in some circumstances. Overuse can result in saturation, which can result in the glove becoming ruined. It’s also important to remember that you shouldn’t have to (or want to) soften your glove’s webbing because it’s thinner than the glove’s body and should break in rather rapidly on its own anyhow.

Don’t: Microwave or Bake It

Microwaves and ovens are only used for cooking food. Gloves are made of leather, and leather does not include any food ingredients. So let’s avoid using the glove in the microwave or the oven! Some people believe that baking leather in an oven softens it. That may be true at first since heat makes leather more pliable, but it is not always the case. Hot air, on the other hand, has a tendency to be dry — and this is particularly true of the hot air that comes out of an oven.

When you bake a glove, the moisture in the leather is drawn out of the leather. That implies that when the glove cools down, it will be completely dry to touch (and sometimes, brittle). A Wilson A-2000 that had been abandoned in an automobile.

Don’t: Leave Your Glove in the Car

When you leave your car in the sun, it will become quite hot. As a matter of fact, they’re similar to mobile ovens. which has led some individuals to believe that placing an open glove on a hot dashboard could be a better option to microwaving or baking it. However, you’ll receive results that are similar to those displayed above: a glove that has become dried out and cannot be repaired using a glove conditioning solution

See also:  What Is The Name Of The Largest Baseball Team In New York City In Terms Of Titles Won

Don’t: Use Shaving Cream

Barbasol shaving cream, which may be used as a conditioner, is one of the most commonly recommended methods for breaking in a glove. Lanolin, a natural oil derived from sheep’s wool, was used in the manufacture of shaving cream back in the day. Lanolin, it turns out, is a fairly effective leather conditioner. However, lanolin is no longer found in virtually all shaving products nowadays. Barbasol shaving cream contains a trace quantity of alcohol, but not a significant amount. Every jar of shaving cream contains an inordinate amount of chemicals and artificial substances that were not intended for use on skin or in the treatment of leather.

It’s possible that you’ve already figured out that dryness is the adversary of a properly maintained glove.

Besides that, some of the chemicals contain substances that can actually break down and weaken the fibers of leather, making it less durable.

Don’t: Put Your Glove Under a Mattress

Using the mattress approach, you may achieve a similar result to that of glove wrapping: by pressing the glove into a closed posture, you stretch the leather and make it malleable more rapidly than usual. The outcomes of these two techniques, on the other hand, are vastly different. The use of rubber bands or string to secure your glove helps you gently stretch the leather along the crease, resulting in a glove that folds properly. The mattress approach, on the other hand, will result in a glove that is flattened and like a leather pancake.

Putting your glove beneath the mattress can cause the heal (the firm leather bar at the base of the palm) to become unduly compressed, which is a critical component of what gives a glove its shape.

The converse is true: If you fold the heel, you’ll wind up with a loose mitt that you’ll have to squeeze hard in order to keep the ball from coming out.

Frequently Asked Questions

Here are some of the most often asked questions on how to break in baseball gloves, as well as the answers to those queries. What is the best way to break in a baseball glove overnight? Breaking in a baseball glove overnight is not only dangerous, but it may also be detrimental to its leather construction. In principle, submitting a glove to extremely high temperatures (such as an oven) or extremely high pressure (such as being driven over by a car) may soften it in that amount of time. That said, using such procedures will result in a dry, misshapen mitt that performs badly and is not very long lasting.

Is it possible to break in a baseball glove with shaving cream?

Glove conditioners such as triethanolamine (an alcohol), isobutane (an industrial gas product), sodium lauryl sulfate (a detergent), and propane are ineffective since they include chemicals and components that dry out the leather over time.

How to Break in a Baseball Glove Properly – Conclusion

As you begin to work on your new baseball glove, keep in mind that it will take some time for it to become comfortable. People are always eager to provide suggestions for ways to expedite the process, but such suggestions can sometimes cause more harm than good. Grabbing balls with a glove is the most effective approach to break it in quickly. Every alternative approach carries its own set of dangers and drawbacks, and it is best avoided if at all feasible. If you don’t require the glove to be game-ready right away, you can use it during warmups until it is ready to be used in the game.

Using oils and conditioners in moderation while caring for your mitt can keep it looking its best.

The Hitting Vault is the most popular, most trusted and highest rated online hitting community.

It was developed in order to teach athletes how to use their bodies in order to unlock their most powerful swing possible. Its purpose is to assist coaches in obtaining the best possible results from their players. Join and you’ll get access to over 100+ special videos for members, as well as step-by-step instructions, so you’ll know precisely what to do next to unleash your power at the plate when you get there.

How to Break in a Baseball Glove

The glove that a baseball or softball player wears has a unique meaning to him or her. The placement of every crease and seam has been accomplished by means of several catches, grabs, and snagging. A great deal of time and effort has gone into designing that mitt, and it all begins with the break-in period. Before playing, players of all skill levels should break in their gloves by rubbing them together. Breaking in your glove properly may assist to ensure that it is pleasant to wear and slides smoothly with your hand when you need it.

In addition to increasing cohesiveness, breaking in your glove will also assist to reduce any undesired stiffness or rigidity.

When it comes to breaking in your new baseball or softball glove, there are a variety of options.

Utilize these procedures to assist you in breaking in your mitt for a comfortable fit and feel.


Pour a tiny quantity of hot water (150 to 170 degrees Fahrenheit) over any areas of your new glove that you would want to be softer (for example, the thumb). It is not recommended to soften your glove in the microwave or with detergents, since this might cause harm to the leather of the glove. Use a tiny quantity of glove oil, applied with a sponge, to achieve the same results. Glove oil should never be applied directly to the glove. It has the potential to be too concentrated at the place of application, resulting in a wet and heavy patch.


Once the glove has been drenched with warm water or glove oil, begin bending the thumb and pinky back and forth toward and away from each other to begin breaking in the stiff regions of your mitt.

Squeeze the index and middle fingers together. The rear fingers should be pushed down, and the palm liner should be squeezed. Pulling on the web top will allow it to extend a little. To ensure that your glove is totally dry, repeat the process six to eight times more.


With continued usage, your glove should begin to soften in the same way that other leather goods do. You may assist speed up this process by pounding the pocket where you would catch the ball with a wooden mallet or a 5-pound neoprene dumbbell to soften the glove. In addition, pound the web to produce a fold in the area where you want your glove to break. In addition to helping to create a good valley for the ball to fall into, it may also aid to smooth out any undesirable creases for a smooth pocket finish.

Pounding the pocket also helps the leather to adjust to your palm for the ultimate break-in experience by making it more flexible.


With continued usage, your glove should begin to soften in the same way that other leather goods do. – You may assist speed up this process by pounding the pocket where you would catch the ball with a wooden mallet or a 5 lb. neoprene dumbbell, which will soften your glove. In addition, pound the web to produce a fold where you want the glove to break. In addition to helping to create a good valley for the ball to fall into, this can also assist to smooth out any undesirable creases for a smooth pocket finish.

By pounding the pocket, you may also assist the leather mold itself to your palm for the best break-in possible.


When it comes to breaking in a baseball or softball glove, the most enjoyable way is to simply throw it around as much as you possibly can. By playing catch in a series of rounds, your glove will gradually begin to conform to your hand, with the leather becoming looser with each catch. Playing catch on a consistent basis will be the most effective method of ensuring that your glove becomes used to your hand structure, as no amount of oil, cream, or pummeling therapy can compete with a good old toss when it comes to reproducing genuine game sensations.

In-store glove steaming is available to assist enhance the playability of your mitt in a matter of minutes.


Maintaining your glove in the house rather than the trunk of your car or garage can help it last longer and keep its shape in better shape. Do not forget to take good care of the leather on your gloves by putting a tiny quantity of oil or glove conditioning lotion to them on a regular basis throughout the season. Taking the time to treat your glove right before putting it away for the season is also a wise practice. BONUS PRO SUGGESTION: Conditioners and oils should be used sparingly. In fact, over-caring for your glove can be harmful, as the oils can make your glove heavier and even limit its lifespan due to the oils.

No shortcuts can be taken to having a properly broken-in softball or baseball glove, but by following these helpful guidelines and playing as many rounds of catch as possible, your new mitt should be ready to hit the field in no time!

Do you need to get a new glove for the next baseball season? Make sure to review our helpfulPro Tip’s Rundown on how to get a baseball glove that meets your playing demands and budget before making your purchase.

How to Break in a Baseball Glove: Step-by-Step Guide

The truth that gloves need to be broken in before they can function to their full capacity can be attested to by anyone who has played baseball for more than a year or two. When it comes to breaking in and softening your glove, there are a variety of options available. Some of these approaches can be used alone, while others can be used in combination with others. Continue reading to learn about the many techniques for breaking in your glove, as well as the various methods for lubricating gloves.

  • Getting Catcher’s Mitts and First Base Gloves Used to Each Other

Breaking in Fielding Gloves (Baseball or Softball)

You’ll probably realize right away that your fielding glove is rigid and lacks the pocket necessary to collect fly balls and ground balls with ease once you’ve determined your suitable size and style, as well as after you’ve purchased your fielding glove. Forming a pocket in your glove is an important part of breaking in your glove. Forming a pocket may be accomplished in a variety of ways, and the most effective strategy is totally dependent on player choice. There are some gamers who swear by the microwave (although we do not encourage it), while others feel there are better ways to prepare the food.

Here are a few examples:

Tried and True or Traditional Method

If you’re a purist, this will almost certainly be the way you like to use to break in your glove. Simply get a group of buddies and engage in a game of catch. In practice, the more times you squeeze the glove around a ball, the more likely it is that the glove will be fully broken in and ready to use throughout the season. While this procedure is, without a doubt, the most time-consuming, it is also the most effective and most recommended one available. When compared to alternative ways that some players may choose to employ, it significantly lowers the possibility of harming your glove.

Glove Steaming

Glove steaming is a tried and true approach that has been proven to be effective. This is typically regarded as the second-best approach, after playing catch, for catching a ball. Steaming the glove helps to relax the leather and seams, allowing it to be more game-ready before use.

The glove steaming process typically involves the following steps:

  1. Glove conditioner should be applied to the glove to assist in opening the pores in the leather. Steam the glove until it reaches around 150 degrees. Using a glove mallet, break in the glove’s opening

If you happen to be in the vicinity of a MonkeySports shop, you may stop by and get your glove steamed by one of our knowledgeable staff members.

Manhandling a Glove

This strategy is effective for getting rid of some hostility. All you’re doing here is pressing the glove’s pocket to soften the leather and shape the pocket’s shape. This will require you to either purchase a glove mallet (such as the one depicted below) or make your own mallet out of an old baseball to accomplish. We recommend that you get a genuine glove mallet, which is designed to be used with baseball or softball gloves.

Here’s what you need to do:

  1. Put the glove on in the same way as you would typically do
  2. Make use of your throwing hand to hold the mallet and strike the glove’s pocket on a consistent basis. Take the glove off, place it palm side down on the floor, and strike the rear of the glove
  3. This will help to break in the glove even more.

Other methods may instruct you to wet the leather and lay it out in the sun, but we recommend that you avoid using water and sunlight in this process and instead follow the steps outlined above.

The methods described above may all be utilized to break in your baseball fielding glove. The same tactics will apply if you’re wondering how to break in a softball glove; just be sure to use a softball instead of a baseball to guarantee that your pocket ends up being sufficiently sized.

Additional Tips for Breaking in Your Baseball or Softball Glove

When looking at how to break in your baseball glove, you may find yourself down a trail of false information. There are several beliefs, the most of which are incorrect, concerning how to break in your baseball glove quickly. The fact is that the most effective method of breaking in your glove simply requires time and effort. Here are a few additional pointers to keep in mind when breaking in your glove.

Using Baseball Glove Oils and Conditioners

Even though they are not strictly a break-in procedure, glove oils and conditioners are materials that may be used to soften leather baseball and softball gloves without the need of other methods. If you’re thinking of breaking in your glove with oils and conditioners, the first thing you should know is that items like Vaseline, petroleum jelly, extra-virgin olive oil, mink oil, and linseed oil are never recommended. If you intend to use oils or conditioners on your gloves, you should stick to the items that your glove manufacturer recommends using.

Some conditioners are created particularly for leather and are only available through specialized firms.

Apply a thin layer of paint to the glove and massage it in.

How to oil your baseball glove:

  1. Use only the oils and conditioners indicated by the manufacturer. Don’t overdo it with the oils. Remember that a little goes a long way
  2. Avoid using items that are not recommended for use with leather or that are known to dry out fabrics.
See also:  What Does Era Stand For Baseball

Best Baseball Glove Oils and Conditioners

Following up on our earlier discussion, we only advocate utilizing oils and conditioners that have been authorized by the manufacturer. Specific types of leather must be handled in a specific way or else they will become damaged.Here are the best glove oils and conditioners to try:If you want to experiment with other oils and conditioners, you can find them in theGlove Accessoriessection of our online shop.

Glove Wraps and What They Do

The process of breaking in your glove does not come to a stop after that. While the procedures outlined above assisted you in forming a pocket in your glove, you are not yet finished. You’ll still need to wrap your glove, so be patient. Learning how to wrap a baseball glove is a simple process.

Final steps that will fully prepare your glove for baseball and softball action:

  1. Fold your glove in half to protect your hands. The pocket is formed at the point where you see the crease beginning to develop. To begin, fold the glove in half starting at the point where your pinky sits
  2. Continually fold the pinky side of the glove inwards toward itself. Once the glove has been folded in on itself, use a glove wrap, an old set of glove laces, or a pair of shoe laces to secure the glove in place and maintain the folded form. If at all feasible, you should utilize a glove cover that has been designed expressly for this purpose. You can also choose to wrap your glove around a baseball or softball that is placed in its pocket. The use of a softball will result in a larger pocket, which is necessary for people who play slowpitch or fastpitch softball, respectively.

What NOT to do When Breaking in Your Glove

As you read popular baseball or softball forums and articles on various websites, you may come across some fairly unconventional techniques of improving your game. Although many people believe that these break-in procedures are a quick way to soften up a glove, in the long term, they may actually reduce the life of your glove. Some of these strategies may even result in the voiding of the glove’s manufacturer warranty, which is included with the purchase. Here are some of the “tips” that you should avoid at all costs.

Microwaving/Oven “Method”

This is one of the most popular methods of breaking in a glove, although it has the potential to cause irreversible harm. It is possible that using a microwave or an oven can dry up the leather and make the laces brittle, resulting in them breaking. The use of microwaves and baking gloves in the oven is extremely risky, and should not be done. It has the potential to start a fire if left untreated. If your glove has any metal elements, the danger of injury is enhanced.

If you don’t intend to eat your glove for dinner, avoid using the microwave and the oven to prepare it. As an example, consider what happens if you bake your glove in the oven or microwave – both gloves were the same size before they were baked in the oven:

Inside the Car

Similarly to the microwave approach, keeping your glove in a hot car can cause the leather to dry up, causing the laces to become brittle and snapping off (however the chances of your car catching on fire are far less than burning down your kitchen). Keep your hands on the steering wheel at 10 and 2, but leave the gloves at home.

Breaking in Catcher’s Mitts and First Base Gloves

The procedure by which you should break in your catcher’s or first baseman’s glove is quite similar to the process by which you would break in your fielding glove. In particular, catchers and first basemen will find that merely using the glove will be the most effective way. a great deal! Running catch and bullpen sessions will get the task done the most efficiently, albeit not necessarily the quickest way to get it done. Listed below are a few suggestions to bear in mind:

  • Make extensive use of your glove
  • Keep a ball wrapped in your glove at all times. Use only oils and conditioners that have been recommended by the manufacturer. Always avoid putting strange things on your glove. Don’t ever put a glove in the microwave or the oven. Never forget to take your glove out of your car.

Good luck with your new glove, and remember to follow the instructions in our baseball glove care guide to maintain your glove in peak condition! That’s all there is to it! Remember to visit our online store for a broad selection ofbaseball and softball gloves with which you can put your newly acquired break in abilities to the test, as well as all of our other informative how-to tips.

How to Break in a Baseball Glove (4 Easy Methods)

There’s nothing quite like the excitement of purchasing a new baseball glove. From going to the store to selecting the glove that is the proper size and appears to be the most attractive. Everything from purchasing the item to getting it home and removing all of the tags is a fantastic learning experience for young children who are new to the game and even experienced players. Especially if you’ve never purchased a new glove before, you’ll notice one thing immediately away: your glove will be extremely stiff and difficult to squeeze.

Aside from that, when you purchase a glove from a store shelf, the pocket of the glove (where you’ll catch the ball) hasn’t been constructed yet.

When you do this, you’ll be developing the pocket and loosening up the leather, which will make the glove simpler to squeeze and, as a result, easier to catch a baseball in the future.

How to break in a baseball glove is explained in detail in the following steps:

The Traditional Method

Making a catch is an old-school method of breaking in a new baseball glove that is actually fairly simple: When it comes to breaking in a glove and having it mold to your hand, the consensus is that catching a baseball like you would during a game is the best way to go about it. The use of reasoning is prevalent here, as after all, what could be better than the genuine thing? The more times you squeeze your glove around the baseball while playing catch, the more likely it is that the glove will break in correctly.

This is the most successful method of breaking in a new baseball glove, and it has been around for a long time.

If you use the typical approach of breaking in a baseball glove, it will take significantly longer than if you use one of the other methods. But the good news is that you’ll be able to get in some catching and throwing practice while you’re at it.

Steaming Your Glove

Another option that you may do to expedite the process of breaking in your new glove is to steam the glove before you use it. Heating the glove will assist to loosen up the leather and seams, making the glove more comfortable to wear when it is time to put it on your hands. When someone asks how to break in a baseball glove, this is a tried-and-true approach that is frequently regarded as the second-best alternative after the conventional way. Before you begin steaming a glove, you should make certain that you have applied a glove conditioner to the whole glove.

  • Make certain that the conditioner is applied evenly throughout the glove.
  • In order to complete this step, you must steam the glove to roughly 150 degrees Fahrenheit.
  • Similar to this, temperatures exceeding 150 degrees might be detrimental to the leather’s appearance.
  • The mallet is a wooden implement that resembles a little baseball bat in shape and size.

Beating Your Glove

It is always possible to employ this approach if you don’t want to put in the time to break in your glove using the standard method and if you aren’t confident in your abilities to steam your glove. If you need to get rid of some of your hostility, this is an excellent approach to use as well. You will be hammering the pocket of your new glove in this manner, which will soften the leather and aid in the formation of the pocket. The ideal approach to finish this procedure is to get a glove mallet, which was created expressly for this purpose and is quite affordable.

To properly beat your glove, you must first place the glove on your hand in the same manner as you would wear it on the field.

Make sure not to strike it too hard, or you may wind up harming your hand.

Now, using the glove mallet, pound the backside of the glove to break in the leather on that side of the glove.

Wrapping Your Glove

The alternative to the conventional approach is to utilize this method if you don’t want to take the time to break in your glove the usual manner and if you are not confident in your abilities to steam your glove. If you need to release some of your aggression, this is an excellent strategy to use. You’ll be hammering the pocket of your new glove using this approach, which will soften the leather and aid in the formation of the pocket on the glove. The glove mallet, which was particularly built for this purpose, is the most effective approach to perform this procedure.

The first step is to place the glove on your hand in the same manner as you would wear it while playing football.

Make sure not to strike it too hard, or you can wind up harming your hand.

Having sufficiently pounded the pocket, remove the glove off your hand and place it flat on the ground, palm side down. Now, using the glove mallet, pound the backside of the glove to break in the leather on that side of the hand.

Using Oils and/or Conditioners

Glove conditioners and glove oils are frequently recommended by those who want to break in a new pair of gloves more effectively. This is something that, while it may aid in the softening of the glove’s leather, it is not a means of breaking in a new baseball glove in its own right. In the event that you want to use an oil and/or conditioner, keep in mind that you should do so in combination with one of the ways outlined above. One very essential point to remember is that you should only use glove oils and/or conditioners that are suggested by the company that makes your glove.

If this is not the case, you may always contact the manufacturer directly, visit their website, or speak with one of the knowledgeable staff members at a sports goods retailer.

These items may actually cause damage to the leather of your glove, rather than assisting it.

Finally, if you opt to use glove oils and/or conditioners, make sure not to apply too much oil to the gloves themselves.

Other Things You ShouldNotDo to Break in a Baseball Glove

It is possible that you may hear of additional techniques of breaking in a new baseball glove that you should avoid doing entirely. Making a new baseball glove in the microwave or oven is perhaps the most common alternate method of doing this task. People believe that heating the glove will soften the leather in the same way as steaming does, and they are correct. Ovens and microwaves, on the other hand, will heat your glove to a significantly higher temperature than the 150 degrees advised by the steaming method.

  1. The leather of your new glove will dry out as a result of this, and the laces will become brittle, which will most likely result in the laces breaking.
  2. In this manner, it’s evocative to garments shrinking in a clothes dryer that’s been set too high.
  3. If the glove is exposed to very high temperatures for an extended period of time, it may catch fire.
  4. Others like to keep a new baseball glove out in their car or outside in the sun for a period of time, which will allow it to break in more quickly.

This approach does not provide the same fire hazard as baking or microwave-cooking a glove; nonetheless, it is still not recommended.


Purchasing a new baseball glove is one of the most thrilling experiences a young baseball player can have. However, before they will be able to make appropriate use of their glove, it is critical that they break in the glove to ensure that the leather softens and the pocket forms properly. There are several techniques for accomplishing this that you may discover on the internet, but you should stick with one of the three secure approaches that are outlined above. It is not recommended to bake or microwave your new baseball glove, nor should you leave it out in the sun or in a hot car for an extended period of time.

Make certain, however, that you are only utilizing materials that have been permitted for use by the glove’s maker before you begin.

This is the final step in ensuring that your new baseball glove performs to its maximum potential for you in game settings.

How To Break In A New Baseball Glove

You may acquire abaseball glove that is the right fit and is comfortable, but just as with a new pair of shoes, it will require some “breaking in” before you can obtain the best results while using it on the field. Especially if you’ve just purchased a new baseball glove, you’ll undoubtedly want to be able to use it immediately away without experiencing any stiffness. It takes time for a glove to “naturally” break in through wear over time, and this takes time. Fortunately for you, there are more expedient options!

You should keep in mind that the strategies for breaking in a baseball glove are the same techniques for breaking in a softball glove as well.

How To Break In a Baseball Glove Overnight

This procedure is one of the safest ways to break in a baseball glove in a short amount of time. This video demonstrates how to oil a baseball glove as well as other alternative baseball glove oils (since you might not havebaseball glove oil). You may also use these techniques to soften an old baseball glove if you’re seeking for instructions on how to soften an old baseball glove. However, before you begin, be sure you fully clean your old glove using the right baseball glove cleaning solutions, such as this one.

  1. Take a look at this video: ” frameborder=”0″ allow=”accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture” allowfullscreen=”accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture” “The Dark Knight Rises: What Went Wrong?” is the title of the article.
  2. Oils, rather than conditioning creams, perform far better in this manner.
  3. Fill a spray bottle with oil and squirt it all over the glove; if you don’t have a spray bottle, dab the oil on with a towel to get it all over.
  4. Bring the water to a boil in a pot, then set the rack on top of the pot and the glove on the rack to finish cooking.
  5. Steam it for 3 minutes at a time.
  6. Step Three: Turn off the heat and let your glove to absorb the remainder of the steam from the stove.
  7. Remove your glove from the water.

How To Break In a Baseball Glove In The Oven / Microwave

In my honest view, baking a baseball glove in the oven or using a microwave to bake a baseball glove are both bad ideas in my opinion. However, if you require a short break in, follow these steps:

See also:  Outfit How To Wear A Baseball Jersey

Oven Method

Step one: Massage the glove foam treatment into the palm of your hand and put it aside for a few minutes. Step Two: On an oven rack, spread a piece of fabric to use as a glove resting surface. The oven should be preheated at 300 degrees Fahrenheit. Place your glove on the cloth and let it there for 3–4 minutes. Do not go longer than 4 minutes! Here’s an example:” frameborder=”0″ allow=”accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture; swiping” allowfullscreen “The Dark Knight Rises: What Went Wrong?” is the title of the article.

Microwave Method

In step one, massage the glove foam treatment into the whole glove and put it alone for a few minutes to work its magic. Step Two: On an oven rack, spread a piece of fabric to use as a glove resting platform. Preheat the oven to 300 degrees Fahrenheit (150 degrees Celsius). 3-4 minutes after placing your glove on the fabric Continue to the end of the 4-minute limit. Here’s an example:” frameborder=”0″ allow=”accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture;” frameborder=”0″ allowfullscreen “The Dark Knight Rises: What Went Wrong?” is the title of a documentary film.

Final Thought

So there you have it, a comprehensive list of the many methods for breaking in your baseball glove. To enjoy your new baseball glove, follow these instructions carefully and with prudence. This page was last updated on

How to Break in a New Baseball Glove

Documentation Download Documentation Download Documentation A new baseball glove may seem stiff and clunky when first put on. It may even make it more difficult to participate in the game. There’s always the option of waiting for your glove to break in on its own, but this can take a long time. There are, fortunately, less time-consuming alternatives to breaking in a new baseball glove. The following recommendations will help you make your glove feel like a second skin again, allowing you to return to your game with renewed focus and concentration.

  1. 1 Obtain a bottle of baseball glove conditioning oil. The majority of glove manufacturers provide oils that are particularly prepared to treat their gloves. Applying a tiny quantity of conditioning oil to the leather in the pocket of your glove can soften, enhance, and maintain the leather in the pocket.
  • As a low-cost alternative to conditioning oil, you may use some shaving cream containing lanolin
  • Nevertheless, do not apply too much oil or cream to your glove. If you apply too much, the leather will begin to disintegrate quickly. Use only enough to lightly cover the whole pocket with a thin layer of paint.

2A baseball glove or a softball glove should be used. They are not the same thing at all. Softball gloves feature significantly wider pockets in order to accommodate the slightly larger ball used in the sport. Advertisement 3Put a ball in the glove of your choice. Put it in the “sweet spot” of your mind. When you catch the ball in the sweet spot, it is in the bottom part of the webbing between the thumb and forefinger, which is where you would ideally catch the ball. 4 Wrap a number of big rubber bands around the glove with the ball inside it to keep it secure.

This is done in order to shape the pocket to accommodate the ball.

  • This should not be done with string. An unusual-looking impression around the outside of the glove might be left by a thread or twine that has been tightly wrapped.

5For a few hours, place the glove with the band wrapped around it in direct sunshine (no more). The leather will get warm and pliable as a result of the sunshine. Do not leave the glove on a hot surface for an extended period of time. It’s not something you want to cook. 6Remove the glove from the sun, undo the bands, and remove the ball from the glove. Punching your fist into the glove’s pocket, as well as opening and closing the glove, will shape the glove. Throw the ball forcefully and repeatedly into the middle of the glove’s pocket, then shut the glove over the ball as soon as it touches the webbing of the glove’s pocket.

7Retighten the glove around the ball and secure it with the bands once more.

Choose a location that is out of the way and away from pets and small children (who might disturb the process).

8Go back and get the glove. Remove the bands and the ball from the situation. Your glove should be completely prepared for action. It will become more comfortable to wear as you use it more frequently. Advertisement

  1. 1Condition the glove using a conditioning oil. Coat or spray the glove’s whole surface with a protective coating or spray. It is possible that you may need to apply a little additional to the laces to ensure that they are suitably protected. Allow the glove to soak in the conditioner for a few minutes before wearing it. Then dry the glove with a towel until it is completely dry
  2. 2 To use, place the glove on a rack above a kettle of boiling water and turn on the burner. Make careful to maintain your glove several inches above the water to prevent getting splashed by the water. Cover the glove with a curved lid or a huge upside-down bowl to keep the steam trapped within. Set aside for two to five minutes in the steam, depending on how soft you want the leather to get. You want the glove to achieve a temperature of around 150 degrees Fahrenheit.
  • Glove steaming services are available at a number of sporting-goods establishments. Several retailers will even steam a new glove for free if you purchase it from them.

3Remove the glove from the steaming environment. Remove the pan from the heat and wait until the steam has dissipated before retrieving your glove. Using a cloth, pat the glove dry. The glove should be substantially more flexible as a result of this. 4Using a mallet, shape the glove into the desired form. Fold the glove in half so that the thumb is on top, then use a mallet to smash the heel of the glove close to the thumb side to bend the material. Continue to work your way toward the middle of the glove.

You could want a deep or shallow pocket, depending on your own inclination.

  • A deeper pocket may be created by striking the glove close to the webbing
  • A shallow pocket can be created by striking the glove further toward the palm of the glove.

Turn the glove over and strike the heel of it, roughly where your pinky meets your index finger (figure 6). It should now be considerably easier to open and shut your glove than it was previously. Play some catch to assist in the completion of the breaking-in process. Advertisement

  1. 1At a sporting-goods store, get a baseball-glove foam treatment to protect your gloves. When using this approach, it’s the same as breaking in a new glove for six months: 2Apply the foam and lather it into your glove. Cover the whole surface of the glove with the adhesive. Additionally, coat the rear of the glove. Wait a few minutes to let the material to soak up the lather
  2. 3 Preheat the oven to 300 degrees Fahrenheit for four minutes. Place the foamed glove on a baking sheet covered with a towel. Place it on the highest rack of the oven.
  • Set a kitchen timer to ensure that you don’t keep the glove in for an excessive amount of time or forget to remove it

4Remove the glove from the oven with care, using tongs. Allow time for it to cool. Remove any residue left behind after the treatment with a clean cloth. 5 Work the glove in all directions, repeatedly, for at least 10 minutes total. Insert a baseball or softball into the sweet spot of your glove, which is the area where you are most likely to catch it. Allow for cooling of the glove around the ball.

  • It is important to note that most glove manufacturers advise avoiding breaking in gloves with chemicals or heat. To put it another way, use caution when taking the actions outlined above. When leather is subjected to excessive heat or chemical treatment, the natural flexibility and comfort are compromised.

Create a new question

  • Question What is the fastest way to break in a new baseball glove? Baseball Coach and Instructor Isaac Hess is the founder of MADE Baseball Development and Champion Mindset Training Program, a baseball training program in Los Angeles, California. Hess has also worked as a professional baseball player and coach. Isaac has more than 14 years of experience coaching baseball, and he specializes in private classes and competitions for young athletes. He has experience playing baseball in both professional and collegiate divisions, having played for teams such as Washington State University and the University of Arizona, among others. Isaac was rated as one of Baseball America’s top ten prospects in both 2007 and 2008, and he was named to the All-Star team in 2007. In 2007, he graduated with a Bachelor of Science in Regional Development from the University of Arizona. Baseball CoachInstructorExpert AnswerSupport wikiHow by unlocking this expert answer from a baseball coach or instructor. Simply pound it into the ground with a ball. Assuming the glove is completely brand new, with hard leather, the better the glove is going to be, the stiffer it is going to be and the longer it will take to break it in — but the longer it will last, the better the glove. So simply toss a ball into the glove’s pocket over and over again until it is caught. You may also apply a small amount of oil, but not too much
  • Avoid going overboard. Everything else is just catch, and more you grow better at it, the more you’ll want to play with someone who can throw hard. If you’re playing catch and putting in a lot of effort, and you’re catching the ball in the pocket, the ball will start breaking in. Question Will olive oil work as a lubricant to break in the glove? Olive oil will cause the leather to degrade. If it’s a low-cost glove, this will suffice
  • But, if it’s a higher-end glove, you should invest in some glove oil. Question Will it be ok if I put the glove beneath my mattress for a week and sleep on it? You can, but you should place something in the pocket of your glove to keep it from becoming entirely flat
  • Question Is it okay to use coconut oil as a conditioner? No, since it may cause the glove to get heavier or the leather to become damaged. Question Could solar ovens be used instead of microwaves in this situation? It is possible, but it comes with the same cautions as using a microwave or an oven. Do not leave it unattended for an extended period of time. Question Should I use a soft ball or a baseball to break in a baseball glove when I first get it? Make use of a baseball
  • Question Is there a difference in glove size between baseball and softball? Softball gloves are often larger in size, however this is not always the case
  • Question I recently purchased a high-quality glove for my son. What is the best type of “pen” to use for writing a name on a dark glove with black ink? A “normal” white Sharpie has never been available to me
  • Only the white “paint” Sharpie has been available. Donald J. Kane is an American businessman. Answer from the Community I’ve always used a permanent marker to label the inside of my gloves’ finger portions on the inside. I never make a mark on the leather on the exterior. Question Is it okay to apply glove oil and conditioner at the same time? Hudson Morgan is a fictional character created by author Hudson Morgan. Answer from the Community Conditioner is mostly used to keep your glove in good condition, whilst oil is more useful for breaking in your glove
  • Question What is the most efficient method of breaking in a glove? Soak it in warm water until the glove is completely saturated. Allow the water to drain completely before wrapping it with a softball. Allow it to rest for a day before drying it in the sun. Toss in your glove cream and mold it with a wooden glove mallet to your liking. Simply place the item in the dryer and allow for some banging about until the leather is soft. Once you’ve taken it out, you’re ready to play catch

More information can be found in the following answers: Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement


  • Plastic gloves should be avoided. They don’t last for very long. It takes time and care to break in a new pair of gloves. Consult with the glove manufacturer to ensure that the method you choose will not violate the guarantee on the gloves. To break in your glove, rub mink oil into the palm of your hand using a soft towel. This will soften the leather on your hand, making the glove simpler to break in. One of the most effective methods to break in a new glove is to just play catch with it for an extended period of time—the longer the better. Professionals will begin by striking their gloves with a wooden mallet, but will often conclude by just playing catch with their gloves. It is certainly possible for them to have a professional break in a glove for them, but they prefer to do it themselves in order to adapt the gloves to their own hands.


  • Rubber bands can create imprints on your glove if you wrap it around your hand tightly. If you want to wrap your glove around anything instead, use an old belt or a piece of cloth, since this will not damage it. When breaking in new, pricey baseball or softball gloves, exercise extreme caution. Using procedures like as oven heating, foams, petroleum jelly, and keeping the glove out in the sun can all end up compromising the aesthetic and lifespan of the glove in the long run. Utilize these techniques sparingly
  • For example, if your child receives a new glove, do not break it in for him/her yourself. Your hand is very certainly larger than theirs, and you’ll end up stretching the inside of the glove out excessively
  • Allowing others to wear the glove before you’ve completed breaking it in is not recommended. When you put on the glove, you want it to feel “just right.”


Things You’ll Need

  • Purchase a new baseball or softball glove. Baseball glove conditioning oil (which may be obtained at sporting-goods stores) or shaving cream, gel, or foam are more options. Rubber bands with a lot of width

About This Article

Summary of the Article A tiny amount of glove conditioning oil or shaving cream enriched with lanolin should be used to break in a new baseball glove before playing. X It is possible to soften and maintain the leather of the glove by using one of these items. After that, stuff a ball into the glove and secure it with many rubber bands around the exterior of it. Allow the glove to sit outside in direct sunshine for a few hours to dry completely. Take out the rubber band and baseball after 2 hours, and then wrap the exterior of the glove with a rubber band to keep the glove in place.

Continue reading for information on various techniques of breaking in your glove, such as utilizing steam.

The writers of this page have together authored a page that has been read 881,844 times.

Did this article help you?

Leave a Reply

Your email address will not be published.