How To Lace Baseball Glove

Lacing Baseball Gloves – Step by step

Every material thing, including your baseball glove, will eventually degrade to the point that it will no longer function. However, there is no need to be concerned because you have choices. Alternatively, you may take your glove into a store or to an individual who will re-lace your glove for you. However, if you want to save money and possibly have a fun little side project at the same time, you can do it yourself for very little money. This tutorial will walk you through the process of lacing baseball gloves on your own.

Lacing Baseball Gloves – Step 1) What you’ll need for Lacing Baseball Gloves

The tools mentioned below will assist you in re-lacing your glove at various stages of the process. Do not rush the process of re-lacing your glove; instead, allow yourself ample time. In the long term, you’ll be grateful that you were patient with the process. A set of tools for lacing baseball gloves

Lacing Baseball Gloves – Step 2) Removing the old laces

  1. For first-timers, it is strongly suggested to disassemble the glove piece by piece (the palm, the web, and so on), rather than disassembling it all at once. This will prevent you from being disoriented and will enable you to recall where each lace should be placed
  2. Each glove has a somewhat distinct lacing pattern, therefore taking images or even video of the present lacing of the glove can help you remember where each lace should be placed when lacing the glove in the future. If the problem is still too complicated, draw a diagram like this one. To thread the needle through the hole, make sure to only thread the needle through one lacing at a time. Punch your way through the glove with the needle, removing the old lace in the process. Once the old lace has been removed, it should be replaced as soon as possible with a fresh one. Once all of the old laces have been removed from the glove, apply conditioner to the glove. Apply a liberal quantity to your hair, making care to massage the conditioner into any areas that you would ordinarily be unable to reach (e.g. between the finger stalls.) Even on the inside of the glove, use it as a moisturizer.

Lacing Baseball Gloves – Step 3) Re-lacing Process: The Palm

The palm of the glove is the most difficult area of the glove to re-lace since it is the most exposed. This is due to the fact that the palm contains both the pinky and the thumb slots, which we must be careful not to damage when re-lacing. We must make certain that we do not enter the pinky and thumb stalls and that we lace around the slots rather than in them. You’ll get a snag in your fingers if your fingers strike the lace every time you put your hand in the glove.

  1. Take one piece of the fresh leather and tie a single knot around the lace in the manner shown below : Insert the needle through the hole on the backside of the pinky and slide it through the top hole by the pinky, starting with the hole on the backside of the pinky. Initially, it appears as though the first hole is not supposed to be there. Using the glove’s palm as a guide, trace the line along the palm. Using this image as a reference, work your way through the holes, in and out, being careful to weave it through the top hole, and then back down (not seen in this image.) Always remember that your laces should be smooth side up (pointing towards you), since this will pay huge benefits in the long term. Make sure the leather is threaded through each top row and through each accessible hole before you continue. The pattern for the palm should be lace, lace, lace, space, lace, lace, lace
  2. The pattern for the fingers should be lace, lace, lace
  3. The design for the toes should be lace, lace, lace
  4. You should avoid lacing baseball gloves over the pinky hole because else you will have to start over. Make use of your thumb to hold up the pinky loop in this manner, and be sure to lace below it
  5. When you go to the webbing region, utilize the hole that is closest to you to tie off a knot

Lacing Baseball Gloves – Step 4) Re-lacing Process: The Heel

The heel will not require any knotting in the same way as the palm does.

  1. You can begin with either the pinky or the thumb on either end of the hand. In either case, you want to begin by inserting your needle from the right to the left side. To begin, make a loop in the first hole and stitch it closed. The needle should be inserted into the first hole that becomes accessible. There will be some extra lace leftover after this project. With this lace, you have a plethora of possibilities. For the majority of Wilson gloves, the lace will go down around three holes, not including the initial hole into which you started. The majority of Rawlings and Mizuno gloves are two sizes smaller. Continue to maintain your thumb on the lace over the two or three holes while lacing with your non-lacing hand. After that, you’ll want to re-enter the first hole and complete a circle around it. Once you’ve threaded the needle through the top hole, the loop will automatically develop. Put as much pressure on it as you wish, but keep in mind that the more pressure you apply, the less flexible your glove will be. Continue into the second hole, following the same procedure as before. When you have finished the outer shell of your heel, insert the needle through the next available hole
  2. Keep any excess lace tucked in beneath your knot until the following step. Keep it from being overly tight, otherwise you’ll have difficulty closing the glove with your thumb. The remainder of your glove can be reattached to the heel after two or three additional spaces. A sample of this will look somewhat like this: Continue in this manner until you have completed the last hole on the heel. Following the completion of the last hole, you’ll want to create the same loop that you did with the first hole on the heel. Incorporate the needle through the first two or three holes, depending on how many holes your glove will allow, then draw it through the loop to create an attractive straight lace. You may now trim away any surplus lace.

Lacing Baseball Gloves – Step 5) Re-lacing Process: Webbing

The re-lacing of each web will be slightly different depending on the type of webbing used. I’ll use an I-web as an example to demonstrate my point.

  1. Thread the needle through the hole, starting at the top left or right hole and working your way down. Now we need to connect the web to the glove, so leave around four inches of leftover lace for tying a knot. Simply draw the lace through the bottom top hole
  2. Once we have gone through the top bottom hole, we will need to go around the other way to complete the process. We’ll thread the needle through the web at the very top of the structure. This is seen in the second figure below. Ensure that there is a little gap between the webbing and the glove. Connect the webbing to the glove’s opposite side using a safety pin. Insert the needle through the top hole on the right side of the needle holder. Remove your hand from the glove and pull through so that the top portion of the web is now attached to both sides of the glove
  3. Once you have removed your hand from the glove, you will be on the other side. In order to ensure that the smooth section of the lace remains visible, thread the needle into the next hole, which should be just beneath the one you just came out of. You’ll come out the other side if you feed it through that hole
  4. Now enter it through this hole
  5. And last, using the lace we had leftover from the beginning, tie a knot with the two surplus laces. It should be in the form of a diagram like this. Maintain the smooth section of each lace so that it is facing away from the others
  6. Then repeat the technique for the bottom half of the web.

Lacing Baseball Gloves – Step 6) Re-lacing Process: Finger laces

Take note of the web spirals in this photograph. Take a look at how they’re pointing to the right. This implies that we must begin on the left side, or on the thumb side for right-handed people, of the keyboard. Take the piece of leather that you’re going to use and cut the end to make it more angled so that it can be threaded through the holes more effectively. Make certain that you are using an appropriate length of lace.

  1. Tie another knot at the end of the lace, and then begin working on the first hole in the direction in which the spirals are pointing. This is what it should look like once the knot is secured and the first hole has been completed. Step one, omitting the knot, is repeated for hole number two. Please pay great attention to where hole2 is located. After passing the needle through the hole on the other side, it will emerge from the bottom of the hole on the opposite side of the hole. Tighten it to the degree that you choose
  2. Returning to the pinky for the second hole, thread the needle through one more to complete the stitch. As can be seen in the image below, it is on the bottom hole. Fill in hole 4 by repeating the previous steps and inserting the needle through the top row of your ring finger. As seen in the figure, you have the option of going under or over the cross lace. Whatever your own taste, it won’t make any difference in the end
  3. Repeat these steps in the same order as the first time. After you’ve finished with the fingers, it’s time to move on to the spirals. To adjust the tightness of the lace, pull it as tight or as loose as you choose. Make your way out of the same hole you just came through. This will result in a pleasing loop. Make sure it’s not too tight, otherwise the structure of your glove may be compromised. When entering hole2, follow the same procedure as described before. Continue to follow these procedures until you reach the final hole. Once you’ve done that, go through the last hole twice more. You’ll want to loop it around the remaining area on the tunnel
  4. After that, you’ll want to take the needle and come through between the webbing and out just adjacent to the webbing. This is the needle that comes out of the other end of the needle. The needle should be inserted into the thumb through the top hole after it has been passed through the opposing end. Because most gloves do not have the hole where the needle can be seen through in the photo, you’ll want to thread your needle through this hole
  5. Otherwise, your needle will become stuck. Once you have passed through the hole that corresponds to you, tie another knot and trim away any extra lace.
See also:  What Baseball Games Are On Tv Today

Lacing baseball gloves may appear to be a difficult process, but with a little perseverance, it can be a fun weekend activity to complete. Check out this video for a nice video to watch that includes instructions.

How to Repair Baseball or Softball Gloves: Relacing Guide

Gloves are a tool that players in baseball and softball spend a significant amount of time breaking in, tweaking, and ultimately preserving. The time will come for every glove when the laces snap or the ball breaks through the webbing, and the last thing any player wants to do is throw away his or her well-conditioned glove and start over from scratch. Even though your fielding glove is, in some ways, an extension of your body, the inevitable day will come where you will need to have it repaired.

Below, you will learn:

  • You should know what supplies you’ll need to replace your laces. How to re-lace your glove, including pictures and detailed instructions. How to repair the web of your glove

What You Need – Tools for Re-lacing

The process of lacing a glove may be completed in a matter of minutes. It’s true that re-lacing can be one of the more challenging forms of softball and baseball glove repair the first few times you do it, but we promise that once you’ve done it a few of times, you’ll feel more at ease with the procedure and will be able to do it without assistance.

If you want to re-lace your glove properly, you’ll need the following tools:

  • In most cases, laces are 72 inches in length and a standard glove will require 3 to 4 laces to be properly fitted. It is necessary to purchase additional supplies if you plan on lacing a trapeze glove, modified trapeze glove, catchers glove, or a first basemen’s mitt. Typically, six will enough
  • Nevertheless, Grooved needle with a U-wire or straight-lace pattern
  • Conditioner
  • sKnife

Many of these goods should be available in theGlove Accessoriessection of our online store, so check there first.

How to Lace a Softball or Baseball Glove

For the time being, it is acceptable if you do not know how to fix a baseball glove. Many individuals are intimidated by the prospect of re-lacing a glove on their own, but the procedure isn’t quite as difficult as it appears. If you follow these simple instructions, you’ll have your glove re-laced in no time:

  1. To ensure that you don’t get lost when removing the old laces that have snapped or ripped, make a plan or take images of the glove from several angles before you begin. In order to avoid getting lost while re-lacing a glove for the first time, you should re-lace it as you go rather than stopping halfway. One lace at a time, one hole at a time, should be removed and replaced
  2. This is the proper method. Immediately after removing the laces, apply conditioner to the glove, paying particular attention to the spaces between the fingers and other locations that would otherwise be difficult to reach while the laces are on. Make careful to rub the conditioner into the whole glove, including the inside
  3. However, use only a small amount and avoid overapplying the product. Before you begin re-lacing the shoes, apply some conditioner to the laces to make it simpler for them to pass through the holes. This will also make it less painful on your fingertips. Make a tiny hole in one end of the lace with your punch using the other end. You should start with the most difficult place to re-lace, which would be the palm area
  4. When you first start lacing, you should make sure that the smooth side of the Lace is visible. Stick one side of the u-wire needle through the hole and tie a knot on one of the opposite sides of the lace. Make your way around the back of your pinky finger, looking for a hole that doesn’t appear to belong there. This is often found on the right side of the pinky finger on a right-handed throw glove, and on the opposite side of the pinky finger on a left-handed throw glove, respectively. Feed the needle and lace through the opening and trace the line all the way down to the palm of your hand. It will be the most difficult to finish the opening few holes of the course. Make an attempt to feel the holes through the underside of the glove with the hand that is not lacing. Using this method, you will be able to make a more accurate assessment and feel the pattern of your glove as well as how you should lace it
  5. On most gloves, the pattern you’ll want to follow for this next series of holes will be lace, lace, lace, space, lace, lace, lace
  6. On some, the pattern will be lace, lace, lace
  7. On others, the pattern will be lace, lace, lace
  8. On some, the pattern will be lace When you get to the location where the web should be, use the hole that is closest to you and tie a knot, leaving enough to be able to tie it up afterwards. Using the same manner as previously, complete lacing around the remainder of the glove, but remember that you will need to re-lace the web before you are through. You can find extensive instructions on how to replace your glove web further down on this page.
  • It is recommended that you acquire 3/16 inch wide laces, with the exception of first base gloves and catchers’ mitts, which should be 1/4 inch wide
  • And If you have a dog in the house, be sure the conditioner you use does not include any animal waste, as they may try to gnaw through your glove. Perhaps you should stick with the brand conditioner that the manufacturer advises or has specifically made for the glove. Keep in mind that when re-lacing the glove, you should avoid covering the finger sleeves on the inner section of the glove, particularly for the pinky and thumb fingers. If you don’t go under these, you’ll be uncomfortable

The methods outlined here will teach you how to properly lacing up a baseball glove like a pro.

How to Replace a Baseball Glove Web

When you removed the laces from your glove to replace them, you also removed the webbing from the glove as well. You don’t have to be intimidated by the prospect of learning how to repair a baseball glove web. The procedure for re-attaching the webbing to your glove will be identical to the process you used to re-lace it. Keep in mind that you must accomplish this step before you can go to the next stage of finishing the laces on the fingers. Choosing to lace the fingers first means that you will have to go backwards in order to get the lace through the funnel at the top of the pocket, which is the top half of the pocket.

However, if your glove is beyond repair, you may always explore our selection of new baseball and softball gloves to replace it.

How to Re-Lace Your Baseball Glove Wrist Strap

Watch this video to learn how to re-lace the wrist strap on your beloved Wilson A2K or A2000 from Shigeaki Aso, the Glove Guru himself. If you already own a Wilson ball glove that you really adore but want to tighten the fit a little bit more, you can easily re-lace the wrist strap on your A2K or A2000. Start with a Wilson A2000 Glove Care Kit or your own glove care equipment to get the job done correctly.

  1. In order to remove the lace from the wrist strap, you must first untie it. To begin, find the wrist strap on your glove’s pinky side, near the Wilson logo on the wrist
  2. Remove the lace and poke a hole in the tip of it before threading it through the piano wire needle
  3. Repeat on the other side of your glove. Make the wrist strap and the wrist base line up by placing them on each side of the pre-punched holes in the leather. Following that, you’ll thread your lace through Holes A and 3 (as shown in the video above), and then thread the needle diagonally under the wrist strap and bring it up through Holes 6 and out the other end. Make careful to leave a few inches of lace at the bottom since you’ll need it later. It will next be necessary to draw through Hole 5 and up through Hole D. Once this has been completed, you will be able to pull the lace down through Hole 5. Take your needle diagonally under the wrist strap and back up through Hole 4 to complete the stitch. Tie the lace ends in a double knot in both holes A and B after pulling them up through Hole B

You’re now prepared to take to the field. Remember, if you require any further information on glove care or break-in, you can always go to our YouTube channel.

How to lace a baseball glove?

Any serious baseball player, pitcher, or spectator will almost certainly acquire a baseball glove at some point in his or her career. If you are serious about baseball, whether for professional purposes or merely to represent your high school team, you will want to learn how to properly lace up your baseball glove before you begin. This is a handbook to assist you in accomplishing your goal. Because you may need to re-lace your baseball gloves from time to time, this is an excellent place to begin.

See also:  What Is The Lsu Baseball Score

How do I know I need to re-lace my baseball glove?

This is partially a matter of personal choice, but it is also dependent on how much the glove’s lacing has been ruined. If you haven’t used the glove for a lengthy period of time and the lacing is beginning to show signs of wear, you may wish to replace it with fresh lacing and start over. If your lacing has just become unfastened, you may rethread it using the same lacing that was previously used.

I need to replace the laces, what tools do I need?

There is a good chance that you already have some of these items in your possession.

However, if you do not have the necessary tools, below is a list of the goods you will require for re-lacing a baseball glove.

  • The laces are, without a doubt, the most significant component. If you plan on entirely re-lacing your glove, you will want a new pair of laces to finish the task. Baseball glove laces may be purchased at sporting goods stores or even online. Because the lacing is constructed of thick leather, you’ll need a wire cutter to trim the extra lace when you’ve finished lacing it. Baseball glove needle: This is specific to lacing a baseball glove, and it appears similar to a standard sewing needle, except that it is thicker and the eye is much larger to enable for the lacing to fit through
  • It is made of stainless steel. The conditioner can be used to lubricate the laces prior to lacing them into the gloves. In addition, it is utilized on the rest of the glove.

Now that I have the tools, what do I do?

To begin, you must first remove the laces from the glove, regardless of whether you are rethreading them or using totally new laces in the future. This is the initial stage in the process for each of those options. In the event that you are apprehensive about re-lacing your glove or if it is your first time, you may take the glove apart piece by piece rather than pulling it apart entirely at the same time. Take a picture of your glove to make this process easier. That way, when it comes time to re-lace your glove, you may refer to the image.

If you aren’t going to use this old lacing again, put it away or keep it on hand in case you need to relace your shoes with it.

I’ve taken the laces out, how do I put them back in?

On the glove, there are a few distinct lacing designs that will be used in different regions. As a result, we’re going to divide them out for convenience of use. When you are re-lacing your baseball glove, you will be able to receive a more complete description of each portion this way. To prepare your lace for lacing, take your old or new lace and condition it with your preferred leather conditioning agent before beginning. Using this method, you may ensure that they are sufficiently lubricated to be bendable and simple to deal with.

Re-lacing the palm

Lacing this section of the glove might be difficult because you must ensure that all of the slots for your fingers are correctly placed and that none of them are cut off.

  • Make a single knot on a piece of your leather lace
  • This will be your finishing touch. Lace should be threaded through the needle. Insert the needle through the top pinky hole on the back of the glove and trace the outline of the hole all the way down to the palm of the glove. Go from hole to hole, in and out
  • In order to keep your lace flat, make sure it is smooth side up, facing you. Lace x3, space, lace x3 should be the pattern in this case. Make certain that you do not lace over the pinky loop
  • Instead, pull it apart and lace under it. When you reach the webbing section, you will find the end of the palm lacing
  • Make a single knot here to bring the palm lacing to a close.

Re-lacing the heel

  • Beginning at whatever end is most convenient for you, thread the needle from right to left. You will be lacing in loops, and the extra lacing may be sewed into the loops, eliminating the need to tie knots in the process. As a result, you must re-enter the initial hole in order to anchor the stitch. Then, using a spiral stitch motion, sew down the three holes (which are common for a baseball glove). Once you have left the region free for your hand to slide into the glove, you may rejoin the remainder of the glove using the same stitches that you used to attach the heel stitch holes to the first section. If you want to keep the lace in place, repeat the loop stitch you used for the first hole at the last hole as well.

Re-lacing the webbing

  • Draw the lace through the top right hole of the I-web with the needle, leaving a small amount of extra as you pull the needle through
  • Once the lace has been threaded through the web, pull it through the bottom top hole of the glove. Afterwards, you must draw the lace through the top portion of the web, leaving a small amount of space between the web and the glove itself. This must be done starting from the outside of the webbing and working your way in to the centre and then out the other side. Put the two extra pieces together once you’ve gathered them all. This should be repeated for the bottom of the site

Re-lacing the fingers

  • Ensure that the lace is securely fastened at the end
  • Notice how the spiral stitching points in your reference photo and how it begins at the appropriate end, which is the top hole of the finger
  • In hole number two, your needle will enter at the bottom of the hole. Continue to use the needle on your first finger, but this time pass it through the bottom hole
  • These movements should be repeated several times, creating a cross shape at the back and front of the fingers. Following the spirals, follow the stitching direction in your picture and begin a spiral stitching pattern. Tie a knot at the very end of the lacing to bring it to a close.

Leather Baseball Glove Lace

Leather Lace that is currently in stock may be used to repair your glove swiftly.

  • Lace is available in over 40 different hues
  • Both standard and petite sizes are available in a variety of colors. There is no minimum order quantity. Purchase one piece or one hundred pieces, depending on your need
  • There is no need to maintain a large quantity of items in stock at your store. The absence of the hassle of dealing with long tannery schedules and logistics. Fast shipping on lace that is currently in stock
  • Lace acquired from the top tanneries in the country.

Matching the team colors of your customer’s organization is no longer a concern. BFG offers lace in a variety of colors, with over 40 options to pick from. And those colors are available in both normal and speciality sizes, with a few specialty sizes available as well. Most baseball and softball gloves are 3/16 inch wide, which is the typical width for both sports. Generally speaking, this type of lace is found on the heel, the palm, the fingers, and occasionally on the uppermost portion of the shoe’s web.

  1. You should double-check your lace before purchasing it.
  2. This is a professional-grade lace.
  3. Lace hues may differ from one tannery to the next.
  4. Alum-based tanning is used by TT to make a firmer lace, which is particularly noticeable on their signature color lace, Havana Tan.
  5. It’s possible that you won’t be able to get from point A to point B because the holes are too small.
  6. When it comes to replacing a glove, there are normally five components.
  7. This changes depending on the glove.

In most cases, one single 72-inch lace is sufficient to complete two portions on fielders gloves. To be on the safe side, you should order at least three pieces to replace all of the gloves in your collection. Catcher’s gloves and first base mitts are among the most popular.

Amazon.com : Professional Baseball Glove Re-Lacer Kit with Tools and Leather Laces : Sports & Outdoors

4.0 stars out of 5 for this product The use of tools and leather was excellent. On August 22, 2020, the United States will conduct a review. Considering that my glove has been in my possession for almost 35 years, it seems to be brand new. The tools and laces were just what I needed to finish restoring my antique glove. Thank you very much.

Reviews with images

On May 21, 2021, a review will be conducted in the United States. Laces are in the color black. Product Dimensions: Deluxe 4-Tool KitVerified Purchase The tools are of high quality. The lace does not meet professional standards. Overall, it’s a terrific beginning place for someone who is just getting started. If you’re re-lacing a high-quality glove, you’ll need some higher-quality lacing. On November 30, 2020, the United States will conduct a review. Laces are in the color of tan. Product Dimensions: Deluxe 4-Tool KitVerified Purchase This kit made it possible for me to relace my beloved baseball glove.

  1. It was completed in a short period of time and turned out beautifully.
  2. Laces are in the color of tan.
  3. In the end, it only took him an afternoon to relace his whole glove, and it now looks brand new.
  4. Laces are in the color black.
  5. Laces are in the color black.
  6. In the United States, the item was reviewed on January 20, 2021.
  7. Product Dimensions: Deluxe 4-Tool KitVerified Purchase In the United States, this item was reviewed on May 13, 2019.Color: Tan Laces Product Dimensions: Deluxe 4-Tool KitVerified Purchase It saves a significant amount of money to do it yourself.
  8. The tools and laces were just what I needed to finish restoring my antique glove.
  9. 4.0 stars out of 5 for this product The use of tools and leather was excellent.
  10. Considering that my glove has been in my possession for almost 35 years, it seems to be brand new.
  11. Thank you very much.
See also:  What Baseball Cards Are Valuable

How To Relace & Repair a Baseball Glove

Do you think your glove might need a little TLC? You hate it, but you know it’s inevitable after years of usage – baseball glove repair or replacement is on the horizon. If you want to be able to perform at your peak, you must have faith in your equipment. A baseball glove is one of the most important pieces of equipment for any player, and it is well worth the time and effort to keep it in excellent working order.

There are a variety of methods for cleaning and repairing your worn-out or damaged gloves. Fortunately for you, the techniques outlined below will aid in the preservation of everything from the leather surface down to the padding and pocket.

How To Relace a Baseball Glove

  1. To avoid getting lost in the process of removing the previous laces that have broken or ripped, take photographs of the glove from several angles before removing the old laces. For the first time, remove and replace one lace at a time until the glove is completely repaired
  2. For the second time, remove and replace two or three lace at a time until the glove is completely repaired Using pliers or a knife, cut away the old laces. Precautions must be taken to avoid damaging your glove. Start from the lowest corner of the pocket and work your way up to the top of the mitt by tying fresh laces in the corners. It is important not to pull too hard since this might cause damage to the seams. Using scissors or a knife, tie laces together two inches from the end of the lace and trim away the excess. This is completely optional! Some players prefer to keep the lengthy laces on their baseball gloves
  3. Once you have finished relacing your baseball glove, you may begin using it again. After each game or practice session, wipe down the leather with a soft cloth to clean and condition it. This will prevent your mitt from becoming too dry. If you follow these instructions, you will guarantee that your baseball glove lasts as long as possible and continues to function at its peak.

Tools Needed for Relacing

When it comes to replacing your glove, you’ll need a variety of tools, including:

  • Laces! On average, you’ll need three to four 72-inch strands of yarn for each glove. The number of strands may be increased to six if the gloves are very big (such as catcher’s mitts or first base mitts). The grooved end of the glove lacing needle allows the lace to be twisted straight into the grooved end of the needle, allowing it to pass through the holes and eyelets of the glove with ease. It’s a brush. It is a hog hairbrush, namely, that is used for cleaning ball gloves. Lace cutters to help you cut through those bothersome laces
  • Just in case, I’ll bring along a tape measure. Conditioner. We recommend our Pro Soft Glove Conditioner for the best results.

How To RepairMaintain a Baseball Glove

While the procedures described above may be used to repair the lace and webbing of a baseball glove, there are some more steps that need be taken in order to understand how to repair and maintain a baseball glove.

  1. The first step in learning how to repair a baseball glove is to clean and condition your leather using only high-quality materials, as described in this article. Together, these chemicals work together to preserve the mitt in good shape while also repelling water at the same time. Make sure you thoroughly investigate any items you want to use in order to avoid damaging your precious asset. When baseball glove repair is performed, some products may cause the leather to get waterlogged, resulting in cracking over time and, in some cases, discolouration of the leather. Instead of strong chemicals that might strip the leather of its natural oils, it would be wise to always attempt to use a soft cloth for frequent cleaning. Be sure to apply a conditioner to every portion of your glove before you begin using it. Use a soft cloth or pad to rub the conditioner into the glove. This will aid in keeping water out of the leather while also making the leather firmer over time. Allow your baseball glove to breathe for two to three days after it has been subjected to a thorough cleaning and conditioning procedure. It is then feasible to bend and shape the leather to its maximum extent while being careful not to break or split the leather, which may still be stiff at this point.

Glove Beyond Repair?

If your baseball glove is beyond repair and cannot be relaced, allow the Glove Experts at JustGloves to assist you in finding a replacement baseball glove. For every player and position on the field, we have a pair of gloves. Everything from infielders to outfielders to pitchers and everything in between. Whatever you’re looking for, we’ve got it. To speak with a Glove Expert, call 866-321-4568, send an email to [email protected], or use our live chat feature! Don’t forget that we at Click To Catch are always here to help you!

Glovesmith Super Store

Home Bulk Glove Laces
Bulk Laces – Internet Pricing OnlyWe doNOTmix and match colors to achievebundle sizes.Free Ground Shipping – All Prices Include Shipping
Free Pocket laces with the purchase of a lace bundle3 – 10 pack, 10 – 25 pack, 25 – 50 pack.
Hand SelectedAmerican Tanned Hides,BulkLace -Black, Tan,Blue, Camel, Chocolate, Gray, Red, White, Yellow
10each3/16″ X 72″3 pocket laces $38.00
25each3/16″ X 72″10 pocket laces $66.00
50each3/16″ X 72″25 pocket laces $114.00
10each1/4″ X 60″3 pocket laces $42.00
25each1/4″ X 60″10 pocket laces $75.00
50each1/4″ X 60″25 pocket laces $132.00
Other 1/4″ BulkLace Lengths
10each1/4″ X 48″ – Finger Top Laces3 pocket laces $29.99
10each1/4″ X 72″3 pocket laces $48.99
TanBlack Production Cut Laces
Shipping Options: Ground -Free
USPS2-3 Days -$7.00
International
Free Ground Shipping – All Prices Include Shipping

Relace a Baseball Mitt

If so, do you have a new baseball mitt or glove that you’ve just broken in to your liking? Finally, you’ve got the ball at third base under control and the leather is becoming supple. But what happens if the laces break or come loose via one of the holes? Alternatively, your child has worn out his third glove of the season. Consider repairing the mitt rather than tossing it out and buying a new one. It could just work. For approximately $5, you can get yourself a lacing needle and some rawhide lace, and you might just be able to save the mitt for another season or two of use.

Lace.

Step 1: Survey the Damage

What is the extent of the damage? You’ll have to decide if you’ll need new lacing or whether you’ll be able to rethread the existing lacing. What size of lacing will you require? For this specific repair, the lacing had been removed out of all four fingers and had been reattached at the top of the fingers to keep the fingers from coming apart. However, because the lacing itself was in good condition, I was able to utilize the old lacing and store the new lacing for later repair.

Step 2: Plan the Repair

There has been a minor variation in the lacing pattern on each glove that I’ve worked on so far. If at all feasible, match the lacing pattern to the existing one as nearly as possible. This was not a possibility for this repair since the lacing had already been ripped out, making it impossible. I was able to figure out the lacing sequence by glancing at another glove and probing the holes with the lacing needle to see where it came out. If the lacing pattern is difficult to understand, draw a diagram.

Paths where the lacing is outside of the mitt are indicated by dark lines.

The “behind” half of the design is made in such a way that it appears as if you are seeing through the mitt.

Starting from hole 1 on the front of the index finger, the lacing passes through the index finger of the glove and comes out at hole 2 on the back of the index finger (see illustration).

The lacing re-enters the glove through hole 3 and exits the glove through hole 4 on the middle finger of the glove’s index and middle fingers. Upon reaching hole 5, the lacing diagonally crosses across and re-enters the glove. And so forth.

Step 3: Insert the Needle

Insert the needle into the hole. It’s not nearly as painful as it appears. The needle is threaded through the lace in the other direction. Putting the needle in from the right side so that it comes out of the mitt on the left will let the lace to flow from left to right as desired. You should slide the needle into hole 2 such that it comes out of hole 1 if you are following the plan you created in the previous step. As you follow the route backwards with the needle, you will be putting the needle into the higher numbered hole and pulling it out of the lower numbered hole as you proceed to the next hole.

Step 4: Thread the Needle

Lace should be threaded through the needle. Take care not to get the lace knotted up in your hands.

Step 5: Pull the Needle Through

Pulling the needle back through the hole with the lace is a good technique. As you draw the lace through, you may need to twist the tool back and forth and use a little push to get it to go through. Pull the lace through until it is long enough for you to grip it with your fingers. Then you must persevere until you reach the finish line.

Step 6: Tighten and Tie

Steps 3, 4, and 5 should be repeated as many times as necessary. Increase the tension in the lacing, but do not overdo it. Tie the ends together. In the event that there is any extra, cut it off, but leave enough lace at the end so that it is simple enough to reattach if it becomes loose again.

Step 7: Play Ball!

Let’s get this ball rolling!

Be the First to Share

Leave a Reply

Your email address will not be published.