How To Break In A Baseball Glove With Shaving Cream

How To Break In A Baseball Glove With Shaving Cream

Consider the following scenario: you have recently purchased a baseball glove for your position in preparation for your upcoming match. However, you will not be able to break in the glove immediately in order to make it game-ready because you will not have baseball oil to apply to it. What are your plans? The majority of individuals will seek for alternatives to baseball oil, such as mink oil, neatsfoot oil, or olive oil, in order to complete their assignment. But what if you don’t have access to any of these oils and only have shaving cream?

This is one of the most often requested queries we’ve ever received through our e-mail system.

We’ll address that today.

Should You Use Shaving Cream On Your Baseball Glove?

The first and most obvious answer is “No.” If you are concerned about the appearance of your glove and its color, we do not advocate breaking in a baseball glove with shaving cream. However, if you must use it to soften your gloves, there are several precautions you can take to ensure that you obtain the best results possible without being hurt. Don’t worry, shaving cream does not have the same effect on the human body as acid, and it will not damage your glove quickly. However, if at all possible, we recommend that you use the proper baseball glove oil to complete the break-in process.

How To Break In a Baseball Glove With Shaving Cream (If you have to)

As previously said, breaking in a baseball glove with shaving cream is a dangerous endeavor, but it is achievable if you follow a few simple procedures. These steps are not difficult to do. It’s simple, but you’ll need some additional time. So, what is the best way to break in a baseball glove with shaving cream?

  1. Take the appropriate accessories with you: The glove may be broken in using a clean, soft cloth and some shaving cream, as well as a baseball, a wooden or plastic mallet, and some rubber bands. Apply the shaving cream on the towel as follows: Never put any chemicals directly on the baseball gloves themselves. Not only should this not be done with shaving cream, but it should also not be done with baseball glove oil. It will quickly darken the color of your gloves as soon as you apply it. Rub the rag over the inside of your glove: Then, using a circular motion, massage the shaving cream into the glove’s surface. Take care to ensure that you have covered every portion of the glove. Allow for a 24-hour drying period: Allow it to dry in a well-ventilated area where it will receive adequate airflow. Avoid using a heater or exposing it to direct sunlight since heat from the outside will damage the leather. Even if you want to dry the glove with a fan, don’t do it. After 24 hours, wipe the glove with a clean towel to remove any residue: Remove any shaving cream residue from the glove by wiping it with a soft cloth once it has dried. Break the glove using a mallet: It’s time to soften the glove now that it’s broken. Make use of an amallet that is capable of breaking the glove without causing any damage. Hit the glove until you are certain that the glove is completely destroyed
  2. Create the pocket in the following ways: What remains is to complete the final step in preparing your glove for game use. Using the rubbers that you took before commencing the break-in process, stuff a ball inside of the glove and knot it up. Allow it to dry: Keep it in a dry environment and give it time to reconfigure on its own. Keep it for 24 hours, however we recommend that you wait 48 or 72 hours to receive the greatest returns from your investment. If you wait for that duration, your glove should be ready to use.

Best Shaving Cream For Baseball Gloves (Safe option)

To reiterate, shaving cream is not a glove-friendly substance, as we previously said. You simply cannot use regular shaving cream on your baseball gloves, for obvious reasons. The most effective method is to use shaving cream with lanolin. Example:

Barbasol Original Thick and Rich Cream Men Shaving Cream

Check for the most recent pricing information. Barbasol shaving cream is formulated with water and sodium lauryl sulfate, which allows your glove to moisturize more quickly and safer than with other brands. If you use the proper amount of this shaving cream, it will not damage your leather and will not discolor the color of your leather. Make certain that you are using the cream with the assistance of a clean cloth in order to avoid any further color problems. Laureth-23 and propane are two of the most beneficial ingredients in this shaving cream since they allow your glove to reconfigure more easily by soaking off its stiffness.

Consequently, if you plan on breaking in your glove with shaving cream, the Barbasol original thick and creamy shaving cream will be extremely highly suggested to you.

Disadvantages Of Using Shaving Cream On Baseball Gloves

So far, we’ve warned you that using shaving cream to break in baseball gloves is bad for your glove’s health. However, we did not specify how much harm it would do. If you use shaving cream without following the guidelines we laid out previously, a variety of problems can happen to you.

  • It has the potential to damage the leather and reduce its durability. It has the potential to darken the color of the glove. It has the potential to make the glove slippery. Failure to thoroughly dry the product may result in a prolonged reshaping time
  • And

Our Thoughts

Shaving cream is specifically designed for shaving your beard. For whatever reason, it doesn’t make sense to use it to shatter your glove. A decent baseball glove oil, such as Hot Glove Treatment, is inexpensive and quite effective. However, if you don’t have any other alternatives other than using shaving cream, make sure to use as little of it as possible to avoid skin irritation. Reshaping should not be done for the whole 48 hours. After the first 24 hours, remove any remaining residual oil from the glove.

We hope you enjoyed our baseball guide and we wish you the best of luck on your baseball adventure in the future.

Break in a New Baseball Glove with the Shaving Cream Method

When it comes to shaving your beard, shaving cream is specifically designed for you. For whatever reason, it doesn’t make sense to use it to rip your glove apart. Using a decent baseball glove oil, such asHot Glove Treatment, is inexpensive and quite effective. However, if you don’t have any other alternatives other than utilizing shaving cream, make sure you use as little of it as you can get away with. Don’t let it dry for the whole 48 hours before reshaping it! After the first 24 hours, remove any excess oil from the glove.

We hope you enjoyed our baseball guide and wish you the best of luck on your baseball adventure in the future.

How to Break in a Baseball Glove (The Right Way) –

Investing in a high-quality baseball glove is one of the most essential decisions a baseball or softball player can make about their game. FREE 1 Hour Coaching Clinic with MLB Hitting CoachWatch Clinic in conjunction with the MLB Hitting CoachWatch Clinic Now It may make a significant difference in your overall performance if you select the proper glove for your position and playing style. While no one glove can transform you into a great defender, selecting one that fits properly and feels comfortable may help you gain more confidence on the field and produce plays that are more clean and consistent in their execution.

Even if you choose a model that is somewhat below the “elite” level, you should expect to pay between $150 and $250 for a quality leather mitt.

One component of this is ensuring that it is properly broken in.

Unfortunately, there is a lot of disinformation out there about the appropriate and wrong procedures, and if you aren’t cautious, you might end up doing more harm than good.

Here, we’ll discuss how to properly break in a baseball glove and why many of the most popular approaches are really counter-productive.

How to Break in a Baseball or Softball Glove

Greetings and congratulations on your recent purchase! Premium leather gloves are pricey, but they demonstrate that you are dedicated to the game and are prepared to go to the next level. Top models such as the Wilson A-2000 and the Rawlings Heart of the Hideare expensive, but if you take good care of and preserve your new glove, it will be at your side for many seasons to come.

Why Do Baseball Gloves Need to be Broken In?

One of the characteristics that distinguish leather as a valued and flexible material is its long-term resilience. However, unused leather that has just been pulled off the production line is typically as rigid as a rock, and the leather used by baseball glove makers is no exception to this rule. Those of you who have ever attempted to catch a ball with a brand new glove are well aware of the difficulties involved. They’re nearly hard to close, and the ball bounces out as if it had been thrown against a wall of bricks.

The break-in phase might be anywhere from a few days to many weeks, depending on the type of leather used.

How to Break in a Baseball Glove – The Right Way

Nomar Garciaparra, a former Boston Red Sox shortstop, had one rule: no one else’s hand was permitted to be in his glove at any time. Nomar’s rule is one that is commonly observed among great baseball players. Why? Since leather expands and conforms to your hand and motions as you break in a glove, it becomes more comfortable and supportive. When you put on a glove, you want it to feel natural on your hand, as if it were an extension of your arm that you had completely forgotten was even there.

When you use the glove enough times, the glove will organically conform to your hand, creating a bespoke fit and a pocket that is tailored to your specific catching style.

In order to get the best-fitting, best-performing glove possible, you must put it through its paces by actually using it.

It toss, take ground balls, shag fly balls, and anytime you have the opportunity to catch a ball with your hand in a glove, do so.

How to Break in a Baseball Glove Fast

When it comes to breaking in a glove, a mix of warm water and manhandling is the most efficient method.

Shigeaki Aso, a glove expert for Wilson Sporting Goods and one of the world’s foremost authorities on the subject, explains the procedure in the video below. What you’ll need is the following:

  • A pail of hot water (not boiling)
  • A pair of rubber gloves a cup of anything
  • A softer surface (such as a cushion or a rug)
  • Glove mallet/glove hammer (optional).

However, it’s important to note that, despite Aso’s well-deserved reputation, there is considerable controversy about the effectiveness of his technique in general. Aso is a highly skilled leather craftsman who creates some of the best gloves available anywhere in the world. He’s well aware of what he’s doing. Using water to soften the leather makes it simpler to work with, but if the water is not applied appropriately, it might leave the leather dry and brittle. So, if you decide to go this route, make sure to follow the directions to the letter – and keep in mind that making a mistake might result in damage to your mitt.

  1. Glove mallet from the Mizuno brand, with a rounded end.
  2. Using this method, you may loosen up the leather and make it more pliable.
  3. With the glove still slightly damp, you want to concentrate on applying as much pressure as possible to the region indicated by the yellow arrow in the illustration below.
  4. It is at this point that the glove mallet is utilized.
  5. Another fantastic approach to form the pocket from here is to place your hand in the glove and use the mallet to shape the pocket.

Glove Steaming

Steaming your glove is a simple, quick, and effective method of cleaning. The technique, on the other hand, has the potential to harm the leather’s fibers. It is for this reason that steaming will void Wilson’s one-year glove guarantee.) Using steam on your glove can soften it, but it will also decrease its durability. In addition, players frequently report that steamed leather fails to maintain its form, instead continuing to break in until it becomes almost too soft to handle. So, if you’re looking for a game-ready glove right now, this would be a good alternative.

Allowing Dick’s to steam your glove is the quickest and most convenient option.

  1. Steamed gloves are simple to use, quick to dry, and highly effective. But it has been shown that this technique is harmful to leather fibers. It is for this reason that steaming will cancel Wilson’s one-year glove guarantee.) Using steam on your glove can soften it, but it will also reduce its durability. In addition, players sometimes report that steamed leather fails to maintain its form, instead continuing to break in until it becomes nearly too soft to play with comfortably. Consequently, if you want a game-ready glove right away, this may be a realistic solution. Expect the glove to last you no longer than a season, at the very least. You may save time and money by having Dick’s steam your glove for you. In their steaming procedure, there are three steps:

Glove Wrapping

A good supplemental approach to aid in the break-in of your glove is to wrap it around your hand. There are two schools of thought on how to wrap a gift: one believes that a ball should be placed in the pocket and the other believes that it should not.

The only one of those suggestions is right; you should always wrap your glove around a ball that is in the pocket. (You may find out more about why this is the case in the section on the mattress approach, which follows.) Wrapping your glove is a simple technique that takes only a few minutes.

  1. The glove is closed (with a ball in the pocket) by bringing the pinky and thumb together. Make a secure closure for the glove by wrapping it with thread, elastic, rubber bands, or anything else that will keep it in that closed position. Allow it to rest for a couple of days before unwrapping it and repeating the procedure

Wrapping the glove stretches the leather and retains it in place for a longer amount of time, making it simpler to deal with in the future.

Glove Conditioners and Oils

Conditioning and nourishing oils for gloves can be used both during and after the break-in process. The first rule of thumb when it comes to utilizing glove conditioners and oils is to only use items that have been approved by the manufacturer. Don’t apply Vaseline, petroleum jelly, chapstick, or olive oil on your glove since they will harm and/or saturate the leather, according to the manufacturer (leaving it greasy, heavy or dried out). The following are five of the most popular conditioners on the market.

  1. Nokona Classic Leather Glove Conditioner
  2. Mizuno Strong Oil Glove Conditioner
  3. Rawlings Glovolium Glove Treatment
  4. Wilson Pro Stock Glove Conditioner
  5. Wilson Pro Stock Mink Oil Paste
  6. Wilson Pro Stock Mink
See also:  How Is Softball Different Than Baseball

It’s important to remember that a little goes a long way with oils and conditioners. For the most part, you’ll only need to apply a thin layer of coating and gently massage it in with a clean cloth. Essentially, the purpose of these items is to keep leather in good condition while also, in certain instances, softening it. Using too much can result in saturation, which can result in the glove becoming ruined. Another thing to consider is that, in most cases, you will not be required (or even desired) to soften your glove’s webbing, which is typically thinner than the glove’s body and should break in quite rapidly on its own.

The Wrong Way to Break in a Baseball Glove

It’s important to remember that a little goes a long way when using oils and conditioners. It is usually sufficient to apply a little layer and gently massage it into the surface with a clean cloth to get the desired results. The purpose of these items is to keep the leather in good condition while also softening it in some circumstances. Overuse can result in saturation, which can result in the glove becoming ruined. It’s also important to remember that you shouldn’t have to (or want to) soften your glove’s webbing because it’s thinner than the glove’s body and should break in rather rapidly on its own anyhow.

Don’t: Microwave or Bake It

Microwaves and ovens are only used for cooking food. Gloves are made of leather, and leather does not include any food ingredients. So let’s avoid using the glove in the microwave or the oven! Some people believe that baking leather in an oven softens it. That may be true at first since heat makes leather more pliable, but it is not always the case. Hot air, on the other hand, has a tendency to be dry — and this is particularly true of the hot air that comes out of an oven.

When you bake a glove, the moisture in the leather is drawn out of the leather. That implies that when the glove cools down, it will be completely dry to touch (and sometimes, brittle). A Wilson A-2000 that had been abandoned in an automobile.

Don’t: Leave Your Glove in the Car

When you leave your car in the sun, it will become quite hot. As a matter of fact, they’re similar to mobile ovens. which has led some individuals to believe that placing an open glove on a hot dashboard could be a better option to microwaving or baking it. However, you’ll receive results that are similar to those displayed above: a glove that has become dried out and cannot be repaired using a glove conditioning solution

Don’t: Use Shaving Cream

Barbasol shaving cream, which may be used as a conditioner, is one of the most commonly recommended methods for breaking in a glove. Lanolin, a natural oil derived from sheep’s wool, was used in the manufacture of shaving cream back in the day. Lanolin, it turns out, is a fairly effective leather conditioner. However, lanolin is no longer found in virtually all shaving products nowadays. Barbasol shaving cream contains a trace quantity of alcohol, but not a significant amount. Every jar of shaving cream contains an inordinate amount of chemicals and artificial substances that were not intended for use on skin or in the treatment of leather.

It’s possible that you’ve already figured out that dryness is the adversary of a properly maintained glove.

Besides that, some of the chemicals contain substances that can actually break down and weaken the fibers of leather, making it less durable.

Don’t: Put Your Glove Under a Mattress

Using the mattress approach, you may achieve a similar result to that of glove wrapping: by pressing the glove into a closed posture, you stretch the leather and make it malleable more rapidly than usual. The outcomes of these two techniques, on the other hand, are vastly different. The use of rubber bands or string to secure your glove helps you gently stretch the leather along the crease, resulting in a glove that folds properly. The mattress approach, on the other hand, will result in a glove that is flattened and like a leather pancake.

Putting your glove beneath the mattress can cause the heal (the firm leather bar at the base of the palm) to become unduly compressed, which is a critical component of what gives a glove its shape.

The converse is true: If you fold the heel, you’ll wind up with a loose mitt that you’ll have to squeeze hard in order to keep the ball from coming out.

Frequently Asked Questions

Here are some of the most often asked questions on how to break in baseball gloves, as well as the answers to those queries. What is the best way to break in a baseball glove overnight? Breaking in a baseball glove overnight is not only dangerous, but it may also be detrimental to its leather construction. In principle, submitting a glove to extremely high temperatures (such as an oven) or extremely high pressure (such as being driven over by a car) may soften it in that amount of time. That said, using such procedures will result in a dry, misshapen mitt that performs badly and is not very long lasting.

Is it possible to break in a baseball glove with shaving cream?

Glove conditioners such as triethanolamine (an alcohol), isobutane (an industrial gas product), sodium lauryl sulfate (a detergent), and propane are ineffective since they include chemicals and components that dry out the leather over time.

How to Break in a Baseball Glove Properly – Conclusion

As you begin to work on your new baseball glove, keep in mind that it will take some time for it to become comfortable. People are always eager to provide suggestions for ways to expedite the process, but such suggestions can sometimes cause more harm than good. Grabbing balls with a glove is the most effective approach to break it in quickly. Every alternative approach carries its own set of dangers and drawbacks, and it is best avoided if at all feasible. If you don’t require the glove to be game-ready right away, you can use it during warmups until it is ready to be used in the game.

Using oils and conditioners in moderation while caring for your mitt can keep it looking its best.

The Hitting Vault is the most popular, most trusted and highest rated online hitting community.

It was developed in order to teach athletes how to use their bodies in order to unlock their most powerful swing possible. Its purpose is to assist coaches in obtaining the best possible results from their players. Join and you’ll get access to over 100+ special videos for members, as well as step-by-step instructions, so you’ll know precisely what to do next to unleash your power at the plate when you get there.

Can You Break In a Baseball Glove With Shaving Cream?

Okay, so you’ve finally acquired your first proper baseball glove, perhaps a Wilson A2000 or a Rawlings Pro-preference. You know the one, the one that is so rigid that you can’t even close your eyes, much alone play catch with it. You lean down and bang on it with your hands for a few minutes, but it doesn’t seem to be getting any better. Then you consider whether there is anything in your house that you might use to soften your glove. Voila! Shaving cream is a product used to shave. You’ve heard of the practice of using shaving cream before, but you’re not sure if it’s genuine or just an urban legend.

Can you break in a glove using shaving cream?

A baseball glove can be softened by using shaving lotions that include a chemical known as Lanolin. It is possible to apply Lanolin oil on leather to soften, protect, and maintain your glove for many years by using it as a moisturizer.

Whats in shaving cream that helps break in a baseball glove?

Some varieties of shaving cream contain an ingredient known as Lanolin, which is derived from sheep’s wool. Lanolin is a yellowish-colored waxy oil that is generated by the skin glands of sheep. It is a natural moisturizer. These glands release an oil that helps to keep the sheep’s fleece moisturized and protected from the weather. The lanolin is extracted from the wool during the shearing and spinning procedures. A variety of consumer items, including lip balm, shampoo, cosmetics, skin lotion and shaving cream, include lanolin as a natural emollient.

In this way, you can prevent moisture from escaping into the air and drying off your glove.

Which types of shaving creams contain lanolin?

  • If you’re old enough, you might recall your father using a red and white container of shaving cream, known as Barbasol, to shave his legs and arms. Barbasol used to utilize Lanolin oil in its shaving creams to assist keep your skin moisturized while you were shaving
  • However, this practice has been discontinued.

It’s possible that you recall your father using a red and white shaving cream can known as Barbasol if you’re old enough.

When Barbasol made its shaving creams, it used to include Lanolin oil to assist keep your skin moisturized while you were shaving; today, it does not.

  • Barbasol Extra Moisturizing
  • Barbasol Thick and Rich Skin Conditioner

If you are apprehensive about using shaving cream, there are various creams made for gloves that include lanolin oil that you may use instead.

  • Wilson Pro Stock Glove Conditioner
  • Hot Glove Cream Conditioner
  • Wilson Pro Stock Glove Conditioner

How much do I need to use on my glove?

When it comes to breaking in your new baseball glove with shaving cream, it’s always a good idea to start off with a small amount at first. Squirt a tiny quantity (about the size of a golf ball) onto a small cloth, rag, or your fingers and rub it in. After that, apply the cream on the leather and begin to massage it into your glove in a circular motion with your fingers. It’s important to cover the whole glove, paying great attention to the hinge points in particular. Hinge points may be found on the heal and through the palm of the hand, respectively.

Repeat this procedure a few times until you have the desired amount of break in that you require.

Is shaving cream all I need to break in my glove?

However, you can easily just use shaving cream and your hands to handle the glove till it’s broken in until the glove is broken in. However, there is one instrument that may be utilized to assist. Aglove mallet is a kind of mallet. A glove mallet, such as this one from Mizuno, is especially designed to aid in the speeding up of the break-in process during the golf swing. Of course, you are not required to use a glove mallet in this situation. Alternatively, a baseball bat barrel or a rubber mallet might be employed.

Then, using the bat or mallet, strike it in the pocket, web, and hinge points of the heal many times.

Make continuous motions with the glove until you get the desired form.

Is there a better way to break in a baseball glove?

However, although shaving cream may be used to soften a baseball glove, I do not believe it is the most efficient and practical method available. Pouring hot water over the glove is one of the most effective procedures, which I personally utilized on my previous glove. Shigeaki Aso, the famed glove manufacturer, demonstrated this approach on YouTube, which I discovered. He employs a procedure in which he takes hot water (about 150 degrees) and pours it over the glove. After that, he uses a mallet or a tiny dumbbell to work the break spots in the glove to make them stronger.

Once the shaving cream or glove conditioner has dried, you can use it in combination with the approach described above.

This will aid in the preservation of your glove and the prevention of the leather from drying out.

Fortunately, there are several tools available to make this procedure much simpler and more expedient. So get yourself some glove conditioner and a glove mallet and go to work on creating a glove that you can be proud of. And, if you do it well, it will last for many years.

A Breakdown of the Best Ways to Break in a Baseball or Softball Mitt

A baseball or softball glove is one of the few sports goods purchases that isn’t usually ready right away after you leave the store because of the nature of the product. If you wear a glove straight from the store to the field, you’re generally in for a long day on the field. It is likely that the leather will be stiff and difficult to bend. Furthermore, the more costly the glove, the worse it is likely to be because it is made of a superior quality piece of leather. There are a plethora of various methods for breaking in a glove.

The common thread is the application of anything that softens the leather, followed by the use of heat or pressure in some manner.

Here are some of the most effective methods for getting that mitt game-ready:

Softening Agents

Glove oil: This is something that glove makers will promote, and it is generally in conjunction with the oil that they sell to consumers. You should use it to soften the leather, but avoid putting too much on it since it might ruin the glove. In addition, the more oil you use, the heavier it becomes, therefore a thin layer is the most effective method. No, not the gel. I’m talking about the shaving cream. Good old-fashioned shaving cream with lanolin, such as Barbasol or Noxema, is recommended.

  1. Shaving cream works by softening your skin in preparation for shaving, and the same principle is at play here.
  2. Inquire with a cowboy.
  3. Glycerin and lanolin are common ingredients in cosmetics.
  4. Some people, especially major leaguers, are firm believers in it, though.
  5. There are more suitable alternatives.

Heating and Beating Agents

In a chilly, overcast state like Michigan or Ohio, getting enough sunlight may be a hit-or-miss proposition. If you live in Florida or Arizona, this is a convenient and secure choice. Put the softening agent on, wrap the glove over your hand with a ball or two in the pocket, and let it to return to its natural state. Rubber bands or shoelaces should be used to secure the glove, and a ball or two should be placed in the pocket to provide the glove with a spot where the ball can settle very readily when those line drives and fly balls come at you.

  1. The greenhouse effect raises the temperature of your automobile to as high as 150 degrees.
  2. Microwave: Some major leaguers swear by the effectiveness of this strategy.
  3. However, be cautious since this might cause injury.
  4. It had made a mistake, so I punished it by putting it in the microwave for 30 seconds and then taking it out “According to an report, outfielder Torii Hunter said “And it actually felt a whole lot better after that.
  5. Extreme heat has the potential to destroy the glove’s fibers.
  6. (And I strongly doubt that the sports goods store will accept a returned baseball glove that has been fried.) Furthermore, if your glove has any metal grommets, you should not wear it.
  7. Stephen Drew recommends baking it in a conventional oven like a pizza.

There are a multitude of strategies to use in this situation. Some people will use a bat to smash it. The majority of people will place it between their mattress and box springs. It’s possible that some will run it over with their automobile or leave it under a tire.


Why not employ someone to break in your glove if you can get someone to handle your taxes, your cleaning, or your grocery shopping for you instead? Known as a master glovesmith, Dave Katz, proprietor of Katz Sports Shop in Meriden, Connecticut, is a true professional in his field. There’s no indication on how much it will cost or how long it will take, but if you’re serious about it, you can get in touch with Dave via his website. Have you ever left your glove outside in the rain? It’s possible that’s why you need a new one.

See also:  What Is Rosin In Baseball

Remove it as soon as possible using a towel.

Every day, take it outside and play catch with it.

Furthermore, it is nearly a certainty that you will not do any damage to your investment.

How To Break Baseball Glove With Shaving Cream – Simple Guide

As an Amazon Associate, I receive money when people make qualifying purchases via my links. You will not be charged any additional fees. What if you’ve just purchased a new baseball glove and aren’t sure how to break it in without spending the money on a specific leather conditioner or oil? For this problem, there is just one solution: shaving cream. Shaving lotion can soften your new leatherglove and make it simpler to break the baseballglove in the game of baseball. As a result, we will learn how to shatter a baseball glove with shaving cream in this article.

You put some shaving cream on your new leather glove and put it on your hand.

This procedure has been used by professionals for many years, so you can be confident that it is effective.

The procedure is straightforward and may be completed in the comfort of one’s own home.

Should You Use Shaving Cream On Your Baseball Glove?

The first response is “Yes” and the second is “No.” If you are concerned about the appearance of your glove and its color, shaving cream on a baseball glove is recommended. Due to the fact that shaving cream does not include many lubricating characteristics, it will dry out fast on the glove. Aside from the lather, shaving cream includes soap, which can discolor light-colored gloves. Make sure to thoroughly rinse off any traces of soap from your glove before putting it away. If your glove is dark in color and you want to use shaving cream, make sure to do so before it has a chance to dry.

Shaving cream is not corrosive in the same way that acid may damage your baseball glove.

However, if at all possible, it is preferable to break in your baseball glove with the appropriate baseball glove oil. If you use too much of it when breaking in a new baseball mitt, it will still weaken the material of your mitt.

How To Break Baseball Glove With Shaving Cream (Step)

  1. Prepare your hand by placing a dab of shaving cream on the palm of your hand
  2. Make sure the glove is moist with water. In order to protect your glove, apply shaving cream to both the inside and outside of it. To massage the product into all of the nooks and crevices of the glove, use your fingers. When cleaning your new glove, make careful to remove any shaving cream that may have gotten on it. Please give it a thorough drying and allow it to dry in the sun for a minimum of 24 hours. Once they’ve dried out, pound them into submission with a hammer. Fill your pockets with balls or other things to give them a more defined shape so that when someone tosses a ball at you during game time, you don’t lose out on catching it due of its somewhat weird shape

Shaving Cream On Baseball Gloves – A Deadly Mistake

This is something you’ve undoubtedly seen a lot of baseball players do without giving it a second thought, but you might want to give it some serious consideration before copying them. Some baseball glove owners use shaving cream on their gloves to help soften the leather and make it simpler to break in new gloves after they purchase them. This may appear to be a fantastic idea, but it is really potentially harmful and something that no one should attempt to accomplish.

  • This method has the potential to destroy your brand-new baseball gloves. It will almost certainly make your glove slippery, and it will last for many days even if it is totally dried off. It is possible that reshaping will take longer than expected if the material is not cured. It has the potential to turn your leather black or even worse looking


Gloves are an absolutely necessary component of baseball equipment, but even the greatest gloves require some break-in time. Despite your efforts, you will not be able to make your glove game-ready overnight. However, there are several things you can do to help the procedure move more quickly if you like. How to shatter a baseball glove with shaving cream quickly and efficiently is something you should know. My name is Derek, and I’d want to introduce myself. In 2019, I will graduate from high school, where I have been involved in baseball since I was approximately nine years old.

Baseball has provided me with several chances throughout my life, and it is now my responsibility to give back by assisting others in doing the same.

How to Break in a Baseball Glove

The glove that a baseball or softball player wears has a unique meaning to him or her. The placement of every crease and seam has been accomplished by means of several catches, grabs, and snagging. A great deal of time and effort has gone into designing that mitt, and it all begins with the break-in period. Before playing, players of all skill levels should break in their gloves by rubbing them together. Breaking in your glove properly may assist to ensure that it is pleasant to wear and slides smoothly with your hand when you need it.

In addition to increasing cohesiveness, breaking in your glove will also assist to reduce any undesired stiffness or rigidity.

When it comes to breaking in your new baseball or softball glove, there are a variety of options.

Utilize these procedures to assist you in breaking in your mitt for a comfortable fit and feel.


Pour a tiny quantity of hot water (150 to 170 degrees Fahrenheit) over any areas of your new glove that you would want to be softer (for example, the thumb). It is not recommended to soften your glove in the microwave or with detergents, since this might cause harm to the leather of the glove.

Use a tiny quantity of glove oil, applied with a sponge, to achieve the same results. Glove oil should never be applied directly to the glove. It has the potential to be too concentrated at the place of application, resulting in a wet and heavy patch.


Once the glove has been drenched with warm water or glove oil, begin bending the thumb and pinky back and forth toward and away from each other to begin breaking in the stiff regions of your mitt. Squeeze the index and middle fingers together. The rear fingers should be pushed down, and the palm liner should be squeezed. Pulling on the web top will allow it to extend a little. To ensure that your glove is totally dry, repeat the process six to eight times more.


With continued usage, your glove should begin to soften in the same way that other leather goods do. You may assist speed up this process by pounding the pocket where you would catch the ball with a wooden mallet or a 5-pound neoprene dumbbell to soften the glove. In addition, pound the web to produce a fold in the area where you want your glove to break. In addition to helping to create a good valley for the ball to fall into, it may also aid to smooth out any undesirable creases for a smooth pocket finish.

Pounding the pocket also helps the leather to adjust to your palm for the ultimate break-in experience by making it more flexible.


Placing a ball in the pocket of your glove and wrapping it with two or three rubber bands can keep it secure. The bands should be quite snug, but not too tight, and should overlap one another to make a “X” shape when they come together. Allow four to five hours for your glove to get set in this manner. When your glove dries, this will aid in the formation of the desired shape and prevent the glove from reverting to its original shape. After you have removed the ball from the pocket, pound the pocket once again to work the pocket even more.


When it comes to breaking in a baseball or softball glove, the most enjoyable way is to simply throw it around as much as you possibly can. By playing catch in a series of rounds, your glove will gradually begin to conform to your hand, with the leather becoming looser with each catch. Playing catch on a consistent basis will be the most effective method of ensuring that your glove becomes used to your hand structure, as no amount of oil, cream, or pummeling therapy can compete with a good old toss when it comes to reproducing genuine game sensations.

In-store glove steaming is available to assist enhance the playability of your mitt in a matter of minutes.


Maintaining your glove in the house rather than the trunk of your car or garage can help it last longer and keep its shape in better shape. Do not forget to take good care of the leather on your gloves by putting a tiny quantity of oil or glove conditioning lotion to them on a regular basis throughout the season. Taking the time to treat your glove right before putting it away for the season is also a wise practice. BONUS PRO SUGGESTION: Conditioners and oils should be used sparingly. In fact, over-caring for your glove can be harmful, as the oils can make your glove heavier and even limit its lifespan due to the oils.

No shortcuts can be taken to having a properly broken-in softball or baseball glove, but by following these helpful guidelines and playing as many rounds of catch as possible, your new mitt should be ready to hit the field in no time!

Do you need to get a new glove for the next baseball season? Make sure to review our helpfulPro Tip’s Rundown on how to get a baseball glove that meets your playing demands and budget before making your purchase.

Breaking In A Glove

New baseball gloves are frequently stiff and not yet ready to be used in a game setting. Even gloves that have been customized to your playing style, such as custom baseball gloves or custom softball gloves, must be broken in before they can be used on the field for the first time. Many baseball players are curious in how to properly break in a baseball glove, as well as which ways should be avoided. We’ll guide you through best practices, things to bear in mind, things to avoid, and even show you what the experts do in the sections that follow.

Traditional Methods

When breaking in a new baseball or softball glove, purists adhere to established procedures. They just play catch with their gloves for a number of hours each day for several days or weeks until the glove is properly broken in. Despite the fact that this procedure takes longer, it naturally breaks in your glove better than any other approach, and other methods can speed up the process if you want to rush it. Overall, no matter what you do to break in your glove, the more you can play catch and practice with your mitt, the faster it will break in and become more comfortable.

Baseball Glove Oils and Conditioners

When thinking about how to break in a baseball glove, one of the best places to start is by softly applying a thin coat of glove oil to the palm of the hand. Glove oil keeps the leather “alive,” while also providing a softening condition and helping to protect the leather from gaining weight. Apply about a dime-sized amount of glove oil to a sponge or cloth, and then use the sponge or cloth to apply the oil to the regions of the glove that are currently stiff, as shown in the illustration. Begin with the palm and work your way up to the breakpoint of the glove and finally the web of the glove.

  1. Make care to massage the glove oil into the leather in an equal fashion.
  2. Instead, apply the glove oil to the glove’s interior.
  3. Failure to do so may lead them to begin to fracture and the webbing to become loose, resulting in them being unstable.
  4. When it comes to deciding what sort of oil to put on your glove, the majority of individuals (even professionals) go for shaving cream.
  5. It is recommended that you continue to use glove oils and conditioners once your glove has been broken in throughout the season.

However, you must avoid going overboard. Oil should be applied three to four times throughout the season to get the desired results. Then, for the greatest storage results, add oil to your glove one more time before putting it away after the season.

Work the Rigid Parts

When it comes to physically exercising a glove, many players are likewise confused of how to properly break it in properly. One of the most effective methods is to stretch the tight regions and work the leather to aid in the breaking up of the leather. The thumb and pinky are two of the areas that are the most constricting. It is beneficial to draw these sections of the glove towards and away from one another. This aids in the loosening of the binding and leather, allowing the glove to squeeze and catch the ball more effectively.

See also:  How To Draw A Baseball Cap

It is important to vary the amount of manipulation you do with the fingers depending on how tight you wish your finger laces to be.

Soften and Shape the Glove

When it comes to softening and molding a glove, wooden mallets are frequently utilized. Pounding the pocket can aid in the formation of a ball shape, allowing the glove to get more used to gripping a ball. Pluck the glove in various places to loosen the leather and get it ready for play. Make sure you place a ball in the pocket to evaluate the size and form before continuing to soften and shape the leather using a wooden mallet to achieve the best results.

Important Points to Remember

  • The use of too much glove conditioner/oil can harm and decrease the life of a fresh glove. During this time, in a warm environment, let the glove oil to seep into the leather. Play catch every day until the glove is ready to be used in a game. Use only a little amount of the glove oil
  • You may always add more afterwards. Apply glove oil to your glove towards the conclusion of the season to prevent it from becoming brittle. Maintain the form of your glove by storing it in a dry area with a ball in the pocket. Use of neat’s foot oil, linseed oil, or silicon-type spray is not recommended. It is likely that this will cause leather to dry, stiffen, and grow heavy as a result of the closure of the pores. When it comes to breaking in a glove, there is no shortcut
  • Playing catch is still the best method. To avoid overconcentration of the glove oil at the place of application, first apply it to a piece of cloth and then apply to the glove
  • The most difficult leather to break in will almost certainly be a high-quality leather. It is not recommended to break in your baseball or softball glove in the oven or microwave. This will cause irreparable harm to your glove. Do not leave your glove outdoors or in your car while you attempt to break it in
  • Instead, go to a safe location.

Another Method

When it comes to learning how to break in a baseball glove, many individuals prefer to consult with the experts. A professional baseball player will occasionally break in a glove in a manner that is contrary to the recommendations of the glove maker. In order to prevent your gloves from wearing out faster, glove manufacturers do not recommend this practice. Due to the fact that professional baseball players typically receive their gloves free of charge, they are less concerned with lifespan and more concerned with a short break-in time.

  • First, they soak their glove in a pail of extremely hot water for 1-2 minutes, then remove it from the water.
  • Infielders often have one baseball in their pocket, whereas outfielders typically have two baseballs in their pocket.
  • Following that, they will place their glove in a dryer to dry it while the baseball(s) are still in their pocket.
  • After that, they will untie the glove and work in shaving cream containing lanolin, or glove oil, into the glove.
  • In order to utilize glove oil, apply it to a sponge or a cloth first, then use the sponge or cloth to apply the oil to the portions of the glove that are currently stiff.
  • Then, using the glove oil, apply it to all other sections of the glove, including the whole inside, to help moisturize and preserve it.
  • It is now time to begin pummeling the glove with a baseball bat.

Breakpoints should be pummeled in order to make the glove loosen up even more. This will expedite the process, but you will still need to play a lot of catch and use the glove in order to have it completely broken in. Keep in mind that using this approach will reduce the lifespan of your glove.

Shop for Your Next Glove

* Do you need assistance in locating the ideal baseball glove or softball glove? Please contact one of our qualified Glove Experts through email at [email protected], Live Chat, or toll-free phone number: 1-866-321-4568!

How to Break In a Baseball Glove Overnight – Myths and Truths

It’s possible that this is your very first baseball recollection. A parent or someone you look up to offers you a glove and informs you that this glove is now yours to keep and use. But first and foremost, you must break it in. The term “breaking in” a baseball glove raises certain questions. What exactly are you expected to do? What is the best way to tell whether it has been broken into? And what kind of tools should you utilize to get it started? There are many different kinds of myths out there, and it may be difficult to distinguish between myths and realities.


A mallet is used.

Now, let’s separate the myths from the realities and figure out what it means to properly break in a baseball glove.

Why Break in a Baseball Glove at All?

When it comes to breaking in a baseball glove, two characteristics are important: flexibility and malleability. When you get a new baseball glove, it is likely to feel a little stiff at first. The stiffer it is, the less control you have over the movement of the glove, and vice versa. This impairs your ability to make an effective catching maneuver. Each catch will be more controlled if you can get the glove to adapt to your motions as much as possible throughout the catch. Stiffness is the enemy in this situation.

A baseball glove must be able to accommodate two different things.

Every outfielder also understands the importance of having a glove that fits well in your hand.

Breaking in a Baseball Glove: Myths and Truths

When you purchase a new baseball glove, you will immediately note that it exhibits all of the characteristics of new-baseball-glove syndrome. It’s stiff, it’s not form-fitting, and it’s not even really comfy right away, to put it mildly. Myth: It’s impossible to break in a baseball glove quickly. We’ll give this one a half-point for effort. What they’re really saying is that it’s tough to break in a glove as soon as you would want. However, it is possible. During the two-hour journey to a game, there have been reports of catchers putting forth extra effort to make their mitt more flexible.

The truth is that a glove that has been broken in is more comfortable.

It’s like putting on a new pair of shoes for the first time.

They are even capable of causing blisters.

This is a subject that is up for dispute. Using a glove mallet or glove hammer, softening the glove with hot water, and essentially pounding up the baseball glove until it’s closer to the shape you need, for example, is recommended by a leather craftsman. Glove steaming may be recommended by others.

How Do You Break in a Baseball Glove Overnight?

First and foremost, you can do a great deal to break in a baseball glove without having to play catch a thousand times in a row every day. In fact, it’s probably in your best interests to do so. In an ideal situation, you’ll have several weeks to break in a baseball glove. While wearing your new glove, you may notice something odd about it, such as the way it fits your pinky or the way the pocket of the glove isn’t quite set. You can do a lot to break it in overnight by putting it on and off several times.

One method for breaking in a baseball glove quickly

Make sure you have the proper equipment. It will be required to use a bucket of hot water. A cup, a soft place on which to work, and either a glove mallet or a glove hammer to assist in breaking it in would also be beneficial. Make use of the hot water. Pouring it over the glove (as opposed to soaking it in, which would over-saturate the glove) would just soften the surface, allowing you to deal with it more easily and effectively. Use the “hinge” of the glove to complete your task. The region of the glove where the padding beneath your thumb is located is critical in this situation because if this area is not flexible, it will be difficult to properly wrap the glove around a soccer ball.

This approach does not ensure that you will be able to race with a glove that is properly fitted to you.

Can You Use Shaving Cream to Break In a Baseball Glove?

You can, and in some cases, it may be preferable to other methods due to the fact that shaving cream will not cause as much damage. In terms of how “broken in” your glove is, however, it won’t have a significant impact. Adding another element here will almost certainly improve your chances of getting more of the broken-in effect you desire. Some people, for example, will let their baseball glove rest with a softball inside it to help determine the shape of their baseball glove. Others, however, are not in agreement with this method, primarily because they are attempting to catch baseballs, not softballs.

It takes a lot of pressure and a lot of time to achieve the “lived-in” look you want.

Can You Use Vaseline to Break In a Baseball Glove?

Baseball players are fully aware of this since it is one of those “old- timer’s” tactics that they have heard about before. The concept is straightforward: applying Vaseline to the outside of your glove will assist to soften the leather, making it more malleable and accepting to fresh feedback. However, when a manufacturer provides explicit suggestions about what you should use, this becomes an issue. When this occurs, do not apply Vaseline. In certain cases, you may discover that it reacts with the glove in a way that is detrimental to the glove’s long-term longevity.

  1. Vaseline used shortly before a game, for example, will only slightly soften the glove while making it slippery, according to the manufacturer.
  2. Keep in mind that Vaseline is considered a “conditioner.” It is not enough to just apply Vaseline to the affected area.
  3. The term “conditioner” refers to something that helps soften your hair in the same way that a conditioner could.
  4. However, in order to take use of this pliability, you’ll need to provide the baseball glove with extra feedback (for example, by inserting a baseball inside it).
  5. It should only be used in little quantities.
  6. Only when you want to construct the glove later on should you condition the glove.
  7. Using tactics such as wrapping a ball inside the glove and tying rubber bands around it can help you make the most of the time you don’t have to use it, which will save you money in the long run.

You should also avoid over-applying a conditioner if you’re currently using one. This implies that you should avoid using Vaseline on a regular basis, and if you do, avoid using so much that it totally saturates the glove.

Can You Use Olive Oil to Break In a Baseball Glove?

Olive oil is frequently lumped in with Vaseline as a moisturizer. Some ball players’ “home cures” say that you should break in your glove with olive oil, and that it may also be used as a glove conditioner. You can discover these suggestions on the internet. However, you’ll want to make certain that you follow the instructions provided by the glove maker first. Otherwise, handle olive oil in the same manner as you would Vaseline, as described above. That entails being aware of how to use it properly, using it as a “conditioner” rather than a particular breaking-in product, and otherwise minimizing your exposure to it.

Should You Steam Your Baseball Glove?

Sure! This is an excellent approach for causing the least amount of harm to the glove while simultaneously increasing its flexibility for working with. When it comes to glove steaming, one method is to use the conditioner that was advised by the glove maker. Afterwards, you steam the glove until it is soft enough to work with without tearing it. You’ll next use a glove mallet to break in the glove, making it much simpler to fold over a ball when it comes your way in the future.

What Oil Can I Use to Break In a Baseball Glove?

Glove oil made by the manufacturer is generally the finest option. Manufacturers do not provide these recommendations at random; they do it in order to assist you in avoiding damage to the glove. After all, it is their desire that you will appreciate the goods and that you would submit a nice review for them on Amazon. Sure, you can learn everything about microwaving and utilizing warm water for a variety of at-home cures from books and the internet. Furthermore, several oils, such as olive oil, are frequently advised as conditioners for the hair.

There is no alternative for the passage of time.

How Many Gloves Do MLB Players Go Through in a Year?

It’s difficult to get exact data on this, but on average, major leaguers will receive two gloves each spring training. One of these gloves is the “main,” which means it’s the one that will be broken in over the offseason. The second one serves as a backup in the event that the first one fails. Some major leaguers may go through even more of these, breaking in new gloves using gimmicks like petroleum jelly or a wooden mallet, as well as other minor leaguers. Everyone appears to have their own set of tastes.

It’s important to have trust in your glove when a big-time hit comes off of a baseball bat, or whether you’re practicing outfielding against a hitter on a pitching machine.

A glove that has been properly softened and broken in is vital for every position in baseball, whether you’re playing shortstop or first base.

Similar Posts

What is the number of stitches on a baseball? What is the purpose of baseball players chewing gum? Can umpires be thrown out of the game? Baseball Has Unwritten Rules Baseball has unwritten rules. Using Mud to Rub What is the Infield Fly Rule, and how does it work? What is the purpose of athletes wearing eye black? How to Become a Major League Baseball Umpire What does a Minor League Baseball player make in a year? What exactly is a Balk? Assignment has been assigned to you. In baseball, what exactly is a putout?

Leave a Reply

Your email address will not be published.